Home > Hp Scanjet > Hp Scanjet G3010 Lamp Error

Hp Scanjet G3010 Lamp Error

To end the test, disconnect the power cable from the back of the scanner. With the lid open, simultaneously press the Scan Film and Copy buttons (second and third from front of scanner) while turning on the scanner with the power switch at the back. To end the self test, set the power switch to the Off position. Please try again later. check over here

Find Solutions, ask questions, and share advice with other HP product owners. Leave the power module connected to the power source. With the power module connected to the power source, connect the power module cable to the back of the scanner If the power switch located on the back of the scanner Before the LCD stops flashing, press the Scan Document button. http://support.hp.com/us-en/document/c00030441

HP Scanjet 8300 To enter diagnostics mode: Disconnect the power supply from the back of the scanner base. fi6130Z). To end the test, disconnect the power cable from the back of the scanner. I followed lamp error is usually caused by dirty mirrors in the scanner.

Can a layman do it? Run scan test again. ** Make sure the scanner is on the list of the system device ... The ability to move the carriage. Recent products: HP Scanjet G3010 Photo Scanner Troubleshoot a problem Help Other Knowledge Base options Search HP Support Center Most viewed solutions Manuals Setup & install Learn & use Upgrade &

You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. To end the test, disconnect the power cable from the back of the scanner. Question about HP ScanJet Scanners 1 Answer Hp 3500C communication error hp 3500C communication error Error: An error occured communicating with the scanning device. Wird verarbeitet...

Press once to begin a continuous flatbed scan at a designated speed. It has been discontinued get the original regulator hp it work with 12 volt.- 1 .2.5amp. Since we have been using them, they have been a good reliable product. or it's affiliates.

  • Do you wish to proceed to the home page of the new product?
  • If the base unit self test results were as described above, then the test was successful.
  • One of the operators kept saying..

The product could not be added to your profile at this time. https://community.spiceworks.com/topic/191596-scanner-lamp-issue Tthe carriage will start moving back and forth in the full scan bed length. Reply Subscribe RELATED TOPICS: USB controlled power strips Brandon Ricci In Memoriam canon camera error - e32   7 Replies Chipotle OP The Red Pill Jan 18, 2012 With the power module connected to the power source, connect the power module cable to the multifunction cable.

The carriage will continuously move the full length of the scanning bed. check my blog Flatbed Scan Emulation Exerciser – Press the Edit Text (OCR) button – This will begin a continuous flatbed scan at designated speed. During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. Cheers also to you! 0 This discussion has been inactive for over a year.

Wird verarbeitet... Scanner base unit self tests covered in this document HP Scanjet model Power adapter requirements G3010 12 V 1250 mA G4010 24 V 1.5A G4050 24 V 1.5A 2300 12 V You may get a better answer to your question by starting a new discussion. this content Or just drag it here!

Good Luck!! 0 Datil OP [email protected] Jan 25, 2012 at 1:48 UTC Brand Representative for HP Hello, - Scott (Ronald6982), sorry to hear about the error pointing to Expand Popular Products HP ScanJet 2400 Flatbed Scanner 249 Questions HP Scanjet 5590 Flatbed Scanner 110 Questions HP ScanJet 3200C Flatbed Scanner 88 Questions HP Scanjet 4470c Flatbed Scanner 72 Questions To end the test, disconnect the power cable from the back of the scanner.

Wähle deine Sprache aus.

A ... The only way to fix this is to replace the bulb. Press and hold the Copy and E-mail buttons, and connect the power cable to the scanner. Press the Scan Doc button.

Connect the power cable to the back of the scanner. When the scanner LCD changes to flashing double zeros (00), release both of the buttons. Generated Thu, 24 Nov 2016 15:18:02 GMT by s_wx1194 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection http://batteryuniveristy.com/hp-scanjet/hp-scanjet-4370-lamp-error.php It would cost more to replace the scanner assy than a new ...

ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection to 0.0.0.8 failed. The LCD will display Diagnostic Mode. Diagnostic speeds options are 75, 150, 200, 300, 600, 1200, 2400, or 4800 PPI. Question about Scanjet G2410 Flatbed Scanner 1 Answer Lamp error in HP Scanner Lamp error in HP Scanner my HP Scanjet g2410 gives lamps error when the command is given for

The scanning lamp will stay lit and the carriage will continue to move. Loading...Oops :Please try again. You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. The carriage will continuously move the full length of the scanning bed.

Change product Choose from all HP products Enter product serial number Please wait while we process your request. To reset the scanner for testing other buttons, press the desired button. The LCD will display Diagnostic Mode. Did a quick search on your error and most solutions I've read is to turn off the scanner, unplug it and let it sit for a few hours, then plug it

Lift the document cover. If the base unit self test results were as described above, then the test was successful. To end the test, disconnect the power cable from the back of the scanner. This page requires Javascript.

The carriage will continuously move the full length of the scanning bed. Have a manual for HP Scanners? Find by product name or number (e.g.

© Copyright 2017 batteryuniveristy.com. All rights reserved.