Home > Hp Scanjet > Hp Scanjet G3010 Error

Hp Scanjet G3010 Error

Also please exercise your best judgment when posting in the forums--revealing personal information such as your e-mail address, telephone number, and address is not recommended. note: The blue LED located above the buttons on the document cover (TMA) will light up when the power switch is in the On position. I installed the G3010 and no problem. With the lid open, simultaneously press the Scan Film and Copy buttons (second and third from front of scanner) while turning on the scanner with the power switch at the back. check over here

Complementary Content Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones HP does not seem to have a direct download for the 10.6 compatibility. If the base unit self test results were as described above, then the test was successful. Please wait while we process your request. my review here

Click the HP Uninstaller icon. Proffitt Forum moderator / January 22, 2015 12:36 AM PST In reply to: Good News Bad News I expanded the Software section, snapped a screen shot to show that. Preview post Submit post Cancel post You are reporting the following post: HP Scanjet G3010 w/Mac OS 10.6 This post has been flagged and will be reviewed by our staff. Press and hold the Scan Picture and Scan Slides and Negatives buttons on the front panel, and connect the power cable to the scanner.

note: The TMA cable must be connected to perform a self test on the HP Scanjet 3770, since the buttons are located on the TMA (document cover). Follow the wizard prompts to complete the installation. Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew Do you have more than one scanner?

The carriage will continuously move the full length of the scanning bed. However the resulting image had a blue haze down the edges. Disconnect the USB Interface cable and the ADF Accessory cable from the back of the scanner. http://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/HP-ScanJet-G3010-error-message-when-scanning/td-p/1720617 Z7_3054ICK0KGTE30AQO5O3KA3016 hp-feedback-input-portlet Actions ${title} Loading...

Was the information on this page helpful? Leave the power module connected to the power source. Follow the onscreen wizard prompts to complete the installation. Disconnect the USB cable from the product.

Lift the document cover. http://support.hp.com/us-en/document/c00030441 HP Scanjet 4850 and 4890 Disconnect the USB cable from the back of the scanner. To end the test, disconnect the power cable from the back of the scanner. Click Open in the pop-up, and then click Open again.

While pressing the “E-mail” and “Copy” buttons, reconnect the power supply to the scanner. check my blog I had hoped it was a software matter that could be addressed. Click the lock () in the lower left corner to make changes to Security & Privacy settings. Lift the lid and simultaneously press the Scan Film and Copy buttons (second and third from front of scanner) while turning on the scanner with the power switch at the back.

  • Press and hold the Scan and Copy buttons on the front panel, and connect the power cable to the scanner.
  • Leave the power module connected to the power source.
  • Press once to begin a continuous flatbed scan at a designated speed.
  • top HP Scan software available The following HP Scanjet models have HP Scan software compatible with OS X 10.8 (Mountain Lion).

Repeat the above steps to download the HP Scanjet Update for OS X 10.7 and then see the next step. SHOW ME NOW © CBS Interactive Inc.  /  All Rights Reserved. To end the test, disconnect the power cable from the back of the scanner. http://batteryuniveristy.com/hp-scanjet/hp-scanjet-5590-error-8-1-0-1.php top top Troubleshooting error messages received during installation When you try to install older software released prior to Mountain Lion, you might receive the following error message: '...Driver comes from an

The experts there will be more familiare with the device and systems you're using. Check. NOTE: Please DO NOT install older software from any HP CD that might have come with the HP Scanjet.

I will try it, but it will be some time before I can attend to that option.

NOTE: If you are using Windows XP, click Start, click Control Panel, and then select Add or Remove Programs. Reconnect the power supply and turn on the scanner. Initially success in that this time I got a window looking for the hardware (scanner). NOTE: It is important that you reboot the computer when instructed in the following steps.

The three in one is attached via a Cat 5 cable; the flat bed is attached via an USB cable.The problem with the flatbed manifested itself well before the three in Unless the scanner's documentation indicates otherwise, this software is not intended for use on OS X 10.8 (Mountain Lion). Rob Adv Reply November 7th, 2008 #2 Erlander View Profile View Forum Posts Private Message Quad Shot of Ubuntu Join Date Dec 2006 Location Melbourne, Australia Beans 431 Re: HP have a peek at these guys To end the test, disconnect the power cable from the back of the scanner.

Country: United States Select a location Americas Europe, Middle East, Africa Asia Pacific and Oceania Select a language Confirm Back Z7_M0I02JG0KOT530A6KJKFRQ0816 hp-detect-load-my-device-portlet Actions ${title} Loading... Close the document cover. Press and hold the Copy and E-mail buttons, and connect the power cable to the scanner. If the base unit self test results were as described above, then the test was successful.

Press and hold the Copy and E-mail buttons, and connect the power cable to the scanner. top Install the HP Scanjet software to scan in OS X 10.8 (Mountain Lion) To scan in OS X 10.8 (Mountain Lion), use the OS X 10.6 (Snow Leopard) AND the Help Me.. Find Solutions, ask questions, and share advice with other HP product owners.

During a successful base unit self test, the scanner will do the following: The scanning lamp will light up.

© Copyright 2017 batteryuniveristy.com. All rights reserved.