Use Resize to change the size of the scanned image. If the base unit self test results were as described above, then the test was successful. Unplug the power cable from the power source, wait 60 seconds, and then plug it back in. Uploaded on Apr 5, 2009There is something wrong. weblink
The carriage does not move during the self test. In most cases the lamp will cost you more than the scanner did ... During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. if not working replace lamp assembly. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=391317
Yup! The scanner lamp should flash six times while the carriage is still in motion. The scanning lamp will light up and stay lit.
Warranty status:Unspecified Check warranty status Enter product serial number The serial number you entered,, matches a different product than the current product. HP Scanjet G4010 Ensure TMA lid and power are connected. If the power switch located on the back of the scanner is in the On position, then switch it to the Off position. No light or only dim light is visible in the transparent materials adapter After each step, start a scan to see if the scanner is working.
Hev Level 3 Expert 1059 Answers Tony Isted Level 1 Expert 49 Answers gbob59 Level 3 Expert 2963 Answers Are you a HP Scanner Expert? Loredovision 23,437 views 9:27 Clean Inside Flatbed Scanner Glass Dust Removal - Duration: 35:55. I can't locate 'unistall.exe' on installation CD-ROM or in Downloaded W-XP files; but I'm not skilled in file searches in XP. While pressing the “E-mail” and “Copy” buttons, reconnect the power supply to the scanner.
or it's affiliates. When the scanner LCD changes to flashing double zeros (00), release both of the buttons. Check to see if their is no SCSI ID ... A cable might be loose.
If the scanner completes the sequence correctly, the scanner is working correctly. http://www.fixya.com/search/p472933-hp_scanjet_3770_flatbed_scanner/lamp_error The carriage will continuously move the full length of the scanning bed. Find by product name or number (e.g. If the base unit self test results were as described above, then the test was successful.
Press and release the Scan Document button. http://batteryuniveristy.com/hp-scanjet/hp-scanjet-4070-lamp-error.php Lift the document cover. BrokenPrinter1 143,629 views 7:30 Dotto Tech - Season 5 Episode 22 - Digital Photography - Duration: 7:03. Ensure that both the USB cable and power cable are securely connected.
Hello, The lamp error is usually caused by dirty Question about HP ScanJet Scanners 1 Answer HP Scanjet 5590 ...Lamp Error "Bad or fading lamp (error -4430)" Fixable? w2hat are the technical solutions? If the base unit self test results were as described above, then the test was successful.
If the scanner does not complete the sequence correctly there is either a power problem or a problem with the scanner. the scan lamp is defective cahnge to a new one Prev12Next » Not finding what you are looking for? During a successful base unit self test, the scanner will do the following: The blue power LED will light up. Turn it into... - Duration: 1:21.
Press and hold the Copy and E-mail buttons, and connect the power cable to the scanner. Dispatching to a British Forces Post Office? Press and hold the Scan and Copy buttons on the front panel, and connect the power cable to the scanner. For the cost ...
Press and release the Cancel button. Loading...Oops :Please try again. Add to Want to watch this again later? Contact HP if you require assistance or if you cannot correct the problem.
If the base unit self test results were as described above, then the test was successful. To end the test, disconnect the power cable from the back of the scanner. After the carriage moves the full length of the scanning bed a few times, the scanning lamp will blink several times. HP Scanjet 3500 and 3570 This scanner does not have a self test.
The carriage will continuously move the full length of the scanning bed. The TMA lamp should illuminate and the TMA engine should make a single simulated TMA scan pass with the light on. Lift the lid and simultaneously press the Scan Film and Copy buttons (second and third from front of scanner) while turning on the scanner with the power switch at the back. HP Customer Support Support Home Products Software and Drivers Forums Contact Support Search Select your Model Let HP find my products Identify now HP can identify most HP products and recommend
Make sure you installed ... Loading... During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. Dots or streaks appear in the scanned image Check the original slide or negative for damage or debris.
The carriage will continuously move the full length of the scanning bed. Lift the document cover. Lift the document cover.