Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.When a solution is found please mark the post that solves your issue.Every problem has a solution! by lianne on Mar 18, 2009 at 9:12am Add comment Please sign in to comment 0 I recently replaced ink cartridges on my hp 1350. Step two: Try the task again Press the appropriate button(s) on the product control panel to try the intended task again. Follow these steps to perform a partial reset of the product. check over here
Figure 13: Disconnect the power cord Wait 15 seconds. A hard reset should solve such a headache for you. I hoped someone would know what I should look for. Step one: Perform a power reset Press the On/Resume button () to turn on the product.
Figure 44: Lift the scanner lid Place the alignment page face down on the scanner glass in the lower-left corner.Figure 45: Load the alignment page Close the The sequence must be completed within ten seconds. If these steps resolved the issue, you do not need to continue troubleshooting.
I SO badly need this printer to work and I SIMPLY cannot afford a new one. If the alignment page does not print automatically, follow these steps to print one manually: If the product is off, press the On/Resume button () to turn on the product. Do not mix different types, weights, or sizes of paper. After it's done booting, with the printer already on, plug it in.4.
that's not a good sign. The product prints a self-test report. Close the cartridge access door.
Step two: Print a self-test report Follow these steps to print a self-test report.
Figure 73: Lift the scanner lid Place the alignment page face down on the scanner glass in the lower-left corner. http://www.fixyourownprinter.com/posts/36804 Figure 1: HP PSC 1200, 1310, 1340, and 1350 control panel with the lights indicated 1 - On/Resume light 2 - Check Paper light 3 - Check Print Cartridge light 4 See the documentation that came with the HP product for more information. Open the scanner lid.
by GaryCClark on Jan 17, 2011 at 9:56am Add comment Please sign in to comment 0 I have posted before about my 1350 not printing red. check my blog When it changed from E to 1 for a tiny bit..what does that mean? Javier Alonso Gordo 109.904 visualizações 4:42 Impresora HP PSC 1350 - Duração: 2:05. What ever happens that will at least isolate the problem.
I can print fine with plain paper: isn't this machine supposed to be able to use a multitude of photo papers? The product aligns the cartridges.Figure 46: Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking. Reconnect the If the issue persists, continue to the next solution. this content User Agreement, Privacy, Cookies and AdChoice An error (403 Forbidden) has occurred in response to this request.
Whew! - Anonymous 0 PLEASE CAN ANYONE PROVIDE GUIDANCE? Figure 23: Slide the paper width guide in against the edge of the paper Press the On/Resume button () to continue the task. If the problem is either one of these, then you're pretty much out of luck, since these aren't things designed to be fixed by the consumer.
Load plain white paper in the paper tray. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 08-03-2011 06:50 PM I tried your solutions.my computer has been doing this Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Figure 21: Slide out the paper width guide and fold out the paper tray extender Tap the stack on a flat surface to align the edges of the paper.
Processando... Removed the envelope and tried again, same result no goDecided to not print an envelope but another document. With the power on, disconnect the power cord from the rear of the product. have a peek at these guys Solutions Solution one: Turn the All-in-One off and then on again Follow these steps to turn the product off and then on again.
You can change this preference below. Any suggestions??? I have just installed 56 black cartridge, do you think 57 color cartridge is necessary for the printer to copy or print the document? I'm not exactly sure how I resolved the problem, but if I remember correctly, it went something like this:1.
Solution four: Remove and reinstall the cartridges Follow these steps to make sure that both cartridges are installed and seated correctly. I bought a new black 56 cartridge and installed it but I still get the flashing red button. Disconnect the printer from the computer and try deleting the print job. Solutions Solution one: Wait for the All-in-One to complete the job Allow the product to complete the job.