Home > Hp Psc > Hp Psc 1200 Error Codes

Hp Psc 1200 Error Codes

Contents

Carregando... Prisma Cartuchos 24.363 visualizações 11:49 HP PSC 1350 Probleme - Duração: 2:43. Figure : Disconnect the power cord Wait 15 seconds. Reconnect the power cord to the rear of the product. http://batteryuniveristy.com/hp-psc/hp-psc-1200-series-error.php

Do not connect the HP PSC to your computer until after you have completed the software installation. Figure : Do not touch the copper-colored electrical contacts or the ink nozzles Hold the cartridge by its sides, and then slide the cartridge forward into its slot at a slightly Use bottled or filtered water if distilled water is not available. Try the intended task again. http://support.hp.com/us-en/document/c00095908

Hp 1350 Printer Check Print Cartridge Error

Figure : Snap the cartridge into place Close the cartridge access door. Figure : Close the cartridge access door Check the product control panel for blinking lights: If the On/Resume light () blinks, replace the color cartridge. This video shows how to print a test page Click here to see this video in full screen on YouTube. Do not use too much paper.

  • Look inside the product to see where the carriage is stuck, and then check for any torn paper or objects that might be restricting the carriage.
  • Issue: The Check Print Cartridge light blinks In this error condition, the following blinking lights pattern displays on the control panel: On/Resume light: On Check Paper light: Off Check Print Cartridge
  • Press and release the Cancel button () again.

The reset is now complete. Page 44 Homer.book Page 40 Monday, February 24, 2003 6:03 PM Visit the hp psc information center It has everything you need to get the most value from your HP PSC. If the product does not complete the cartridge alignment, it will print an alignment page every time you turn it on. How To Reset Hp Psc 1410 Printer Press and release the Copies button.

Figure : Install the front panel overlay Figure : Correctly installed front panel overlay Reconnect the power cord to the rear of the product. Selecione seu idioma. Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. official site Make sure that the stack of paper is no higher than the top of the paper width guide.

Figure : Open the cartridge access door Wait until the product is idle and silent, and then disconnect the power cord from the rear of the product. Hp Psc 1350 Manual If this happens, press and quickly release the On/Resume button () again. Fila de exibição Fila __count__ / __total__ Fixing a Paper Jam - HP PSC 1200 All-in-One Printer justprintingaround Inscrever-seInscritoCancelar inscrição3.9283 mil Carregando... Fila de exibiçãoFilaFila de exibiçãoFila Remover todosDesconectar The next video is startingstop Carregando...

Hp Psc 1315 Check Printer Cartridge Error

Follow these steps to plug your product directly into a wall outlet. Issue: The On/Resume, Check Paper, and Check Print Cartridge lights blink In this error condition, the following blinking lights pattern displays on the control panel: On/Resume light: Blinking Check Paper light: Hp 1350 Printer Check Print Cartridge Error Press the Cancel button () on the control panel. Hp Psc 1210 Check Print Cartridge Error If the issue persists, continue to the next solution.

justprintingaround 284.320 visualizações 9:34 HP22 Cartridge Refill Ink Recycle mipohk 提供 - Duração: 4:29. check my blog If the product completes the job normally, there is no need to continue troubleshooting. The reset is now complete. Page 5: Get Help Help software for your HP PSC. Hp Psc 1210 Troubleshooting

Securely reconnect the USB cable to the rear of the computer. Check your warranty Manual warranty check * Required fields One or more of the values entered is not permitted. Wait 15 seconds. http://batteryuniveristy.com/hp-psc/hp-psc-1200-system-error.php Solutions Solution one: Turn on the All-in-One Press the On/Resume button () to turn on the product.

If the On/Resume light () does not blink, replace the black cartridge. Hp Psc 1350 Not Printing If these steps resolved the issue, you do not need to continue troubleshooting. If the lights on the control panel still blink, continue to the next step.

Plug the alternate power cord into the wall outlet.

See your browser's documentation for specific instructions. {} Z7_3054ICK0KGTE30AQO5O3KA30B1 hp-support-head-portlet Actions ${title} Loading... If the product does not turn off, continue to the next solution. Figure : Disconnect the power cord Unplug the power cord from the wall outlet. Hp Psc 1410 Check Print Cartridge Flashing Load plain, white paper into the paper tray.

Contact HP to replace the power cord. Figure : The door pins Step three: Clear the paper jam from the front of the All-in-One If you cannot remove the paper jam from the rear of the product, follow Z7_3054ICK0KGTE30AQO5O3KA3073 hp-detect-load-my-device-portlet Actions ${title} Loading... http://batteryuniveristy.com/hp-psc/hp-psc-1200-series-system-error.php Get instant access to support information – 24 hours a day, seven days a week, at no cost to you.

PFAification 22.542 visualizações 2:43 impresora HP PSC 1210 #94 - Duração: 1:13. If the power module has an LED, check to see if the LED lights up. Step 4: Clean the problem cartridge contacts If the light is still blinking, clean the electrical contacts by the procedure below: Gather the following items to clean the cartridge and print If the issue persists, continue to the next solution.

Close the cartridge access door. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. If the product does not turn on, follow the same steps and try a different wall outlet. For more information about scanning your pictures or documents using the HP PSC software, see scan pictures and documents in the HP Photo &...

Figure : Open the cartridge access door Carefully remove any jammed paper from the front of the product. If these steps resolved the issue, you do not need to continue troubleshooting. If the product does not complete the cartridge alignment, it will print an alignment page every time you turn on the product. Solution two: Make sure that the All-in-One is plugged in Follow these steps to make sure that the product power cord is connected to the product and the electrical outlet.

© Copyright 2017 batteryuniveristy.com. All rights reserved.