Home > Hp Psc > Hp 1315 Error Messages

Hp 1315 Error Messages

Contents

Step one: Clean the rollers Gather the following materials: A clean, lint-free cloth, or any cloth that will not come apart or leave fibers Distilled, filtered, or bottled water (tap water Reconnect the power cord to the rear of the product. I found out that the date on both cartridges have already been expired. Wait a minute before continuing on to the next step. weblink

Unplug the power cord from the wall outlet. Figure : Open the cartridge access door Hold the cartridge on its sides, and then slide the cartridge forward into its slot at a slightly upward angle. Only add paper to the tray when the product is not printing. Disconnect the power cord from the rear of the product. http://h30434.www3.hp.com/t5/Inkjet-Printing/Sudden-Print-Cartridge-Error-For-PSC-1315-Unsolvable/td-p/277223

Hp Psc 1350 Check Print Cartridge

Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. You can get a document or photo to test scanning and copying functions as well. Press the On/Resume button () once slowly to turn on the product.

Damaged or dirty paper rollers. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Figure : Disconnect the power cord Wait 15 seconds. How To Reset Hp Psc 1410 Printer This is very frustrating for me because I just purchase new set of cartridges again and this problem still remains the same!

Load plain, white paper into the paper tray. Hp Psc 1350 Troubleshooting The following blinking lights pattern displays on the control panel: On/Resume light: Blinks fast for 3 seconds and then stays on Check Paper light: Off Check Print Cartridge light: Off Black Figure : Reinsert the cartridge Firmly push the cartridge in until it snaps into place. http://h30434.www3.hp.com/t5/Inkjet-Printing/I-have-a-print-cartridge-error-with-my-HP-PSC-1315-all-in/td-p/2301373 Remove any loose paper Do not pull jammed paper Step two: Clear the paper jam from the rear of the All-in-One caution: Never pull jammed paper from the front of the

Figure : Load paper in the paper tray Adjust the paper width guide inward until it rests against the side of the paper. Hp Psc 1210 Troubleshooting Lower the paper tray, and if necessary, slide the paper width guide to its outermost position. Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.When a solution is found please mark the post that solves your issue.Every problem has a solution! Press and release the Paper Type button.

  1. Press and release the Cancel button () again.
  2. If the alignment page does not print automatically, follow these steps to print one manually: If the product is off, press the On/Resume button () to turn on the product.
  3. With the power on, disconnect the power cord from the rear of the product.
  4. I'm having the same problem and none of the suggestions have worked for me.
  5. Step five: Print a self-test report Print a self-test report.

Hp Psc 1350 Troubleshooting

caution: Do not disconnect the power cord during this step. http://h30434.www3.hp.com/t5/Inkjet-Printing/hp-psc1315-suddenly-gives-me-a-quot-Check-Print-Cartridge/td-p/1562999 Then, check to ensure the USB cable is connected securely to both the computer and the printer. Hp Psc 1350 Check Print Cartridge Figure : Open the cartridge access door Carefully remove any jammed paper from the front of the product. Hp Psc 1410 Check Print Cartridge Flashing I remember thattrying different cartridges didn't get rid of the error.

Look inside the product to see where the carriage is stuck, and then check for any torn paper or objects that might be restricting the carriage. have a peek at these guys Figure : Lift the scanner lid Place the alignment page face down on the scanner glass in the lower-left corner. Figure : Load the alignment page Close the scanner lid, The product aligns the cartridges. Figure : Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking. First Time Here? Hp Psc 1210 Check Print Cartridge Error

If you are using letterhead, insert the top of the page first. Step one: Disconnect and then reconnect the USB cable Disconnect the USB cable from the rear of the product. Press and hold the Cancel button (), and then press the Start Copy Color button. check over here If these steps resolved the issue, you do not need to continue troubleshooting.

Figure : Do not touch the copper-colored electrical contacts or the ink nozzles Hold the cartridge by its sides, and then slide the cartridge forward into its slot at a slightly Hp Psc 1350 Error Code E Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎06-01-2013 07:16 AM Hi out there!I have the same problem with me Do not use a power strip or surge protector.

So, there I am seeking for a helping hand from you in order to solve this problem!

Figure : Disconnect the power cord Unplug the power cord from the wall outlet. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. If you do, and if the HP software is installed on the computer, you should have seen a message displayed on the computer. Hp Psc 1350 Manual caution: Remove the paper carefully.

Press and hold the Cancel button (), and then press the Start Copy Color button. The product aligns the cartridges. Figure : Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking. show more Hi Richard, Thanks for the quick response, but I did not work! this content Videos English Open Menu English Deutsch Español Français Português 中文 한국어 † The opinions expressed above are the personal opinions of the authors, not of HP.

Let me know if this works for you. Then slide the cartridge out of the carriage. Clean the print cartridge contacts. Solution two: Install the cartridges Follow these steps to install the cartridges in the product.

Reconnect the power cord to the rear of the product. The presence of an E, however, does not affect the meaning of the blinking lights, and can be disregarded for troubleshooting purposes.

© Copyright 2017 batteryuniveristy.com. All rights reserved.