It remains a mysterious singular occurrance. The product prints a self-test report. Solution four: Remove and reinstall the cartridges Follow these steps to make sure that both cartridges are installed and seated correctly. Step two: Print a self-test report Follow these steps to print a self-test report. navigate here
Solutions Solution one: Turn the All-in-One off and then on again Follow these steps to turn the product off and then on again. The rear access door might not be closed or is not locked into place. Step one: Clean the electrical contacts on the cartridges and inside the product Gather the following materials: Dry foam rubber swabs, a lint-free cloth, or any soft material that will not While holding the Cancel button (), press and hold the On/Resume button (). http://support.hp.com/us-en/document/c00094661
If these steps resolved the issue, you do not need to continue troubleshooting. Reply 0 0 stevinsonboy Tutor Posts: 17 Member Since: 01-03-2011 Message 4 of 10 (2,628 Views) Report Inappropriate Content Re: I have a print cartridge error with my HP PSC 1315 WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden The next video is startingstop Wird geladen... Torn, wrinkled, or damp paper loaded in the paper tray.
Press and release the Cancel button () again. When I have both Ink cartridges in, I get the check print cartridge error pop up. Connect the alternate power cord to the rear of the product. Hp Psc 1410 Check Print Cartridge Flashing Hinzufügen Möchtest du dieses Video später noch einmal ansehen?
An alignment page prints automatically. caution: Do not remove jammed paper at this stage. Figure : Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking. Figure : Remove scraps of paper Gently push the pins on the right end of the rear access door into the holes on the right side of the rear access area,
Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 01-09-2013 07:22 PM Went to town yesterday but both cartridges 56 & How To Reset Hp Psc 1410 Printer Anmelden 16 Wird geladen... Figure : Load the alignment page Close the scanner lid, and then press the Scan button on the control panel. This machine is several years old and still in impeccable shape.I have only used this machine for scanning.
Figure : Open the cartridge access door Press lightly on the top of the cartridge that you are removing to release it from its slot. Torn pieces of paper from a previous jam are stuck in the product. Hp Psc 1350 Check Print Cartridge Step 4: Clean the problem cartridge contacts If the light is still blinking, clean the electrical contacts by the procedure below: Gather the following items to clean the cartridge and print Hp Psc 1350 Troubleshooting Unplug the printer from the back while it is still on. 3.
Figure : Lift the scanner lid Place the alignment page face down on the scanner glass in the lower-left corner. Figure : Load the alignment page Close the scanner lid, check over here When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Source(s): hp psc 1315xi printer giving error message quot check print cartridges quot: https://biturl.im/0AOMW Rozina · 1 year ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · SINCE AT THAT POINT THE USB CABLE IS DISCONNECTED FROM THE COMPUTER. Hp Psc 1210 Troubleshooting
When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Pulling paper from inside the front cover can cause mechanical damage to the product. Step one: Remove any loose paper Remove any loose sheets of paper from the input tray and the output tray. his comment is here When only the On/Resume button () is blinking, release both buttons.
i feared having to replace it and am glad I didn't. Hp Psc 1350 Error Code E Wird geladen... Press lightly on the top of the cartridge that you are replacing to release it from its slot.
Although I am an HP employee, I am speaking for myself and not for HP.--Say "Thanks" by clicking the Kudos Star in the post that helped you.--Please mark the post that Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Hp Psc 1350 Manual Reconnect the power cord to the rear of the product.
Do not hold the button down. Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray. Step one: Perform a power reset Press the On/Resume button () to turn on the product. weblink Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 06-07-2012 06:52 PM My HP PSC 1315 was working fine.