Right click and copy the file and paste it on the desktop. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. With the product turned on, disconnect the power cord from the rear of the product. You May Also Like How to Get Rid of HP Printer Messages Hewlett-Packard printers are known for their ease of use. his comment is here
This should take only a few seconds. The firewall built into Windows XP and other third-party firewall applications can prevent the HP software from successfully installing the printer. Follow these steps to disable the firewall: Do one of the following: In Category View, click Start, Control Panel, and then click Internet Connections. Close the cover on the product.
Figure : Close the cartridge cover Close the cover on the product. Press the Power button () to turn the product on. On the report is a section on "Ink Service Module".
Try accessing toolbox, if still gets the error message, proceed to step 3. note: Make sure you reinstall or replace the tri-color cartridge. Make sure that the carriage can move freely across the width of the product. Hp Deskjet 460 Printer Manual Dip a swab in the clean water and squeeze it to remove most of the moisture.
The ink service module might overflow. Hp Officejet H470 Ink Service Module Reset Solutions Follow these solutions in the order presented to clear the paper jam. NOTE: Do not turn the product upside down when removing the ink service module as this might cause wet ink to flow out of the module. Solution two: Clear the paper jam Follow these steps in the order presented to resolve the paper jam. Step one: Remove loose paper from the tray Remove any loose sheets
Click Add/Remove Programs. Hp Officejet H470 Cartridge Stalled Reconnect the power cord to the product. warning: You must disconnect the power cord to move the carriage by hand and reset the paper feed mechanism without risk of electrical shock. Figure 25: Close the cartridge cover Close the cover on the product.
Close the cartridge cover to secure the cartridge into place. Carefully remove all traces of paper that you can find. Hp Officejet H470 Ink Service Module Step two: Clear the paper jam from the output slot Follow these steps if the paper is jammed in the output slot. Hp Officejet H470 Reset Carefully remove all traces of paper that you can find.
If the paper tears, part of it might remain inside the paper path and damage the product. this content Unplug the power cord from the wall outlet. Solution No action is required when the Power light blinks. Open HP Solution Center: Windows XP: On the Windows taskbar, click Start, click All Programs, point to HP, and then click HP Solution Center. Hp Officejet H470 Troubleshooting
The HP 460 printer is reset when the power light stops blinking and stays on steady. If the test page does not print, continue with the next solution. The product turns on automatically. weblink Carefully remove all traces of paper that you can find.
Verify that the product is plugged directly into a wall outlet or a dedicated surge protector. Hp Officejet H470 Resume And Power Light Blinking Gather the following items: Clean distilled water. Close the cartridge cover to secure the cartridge into place.
Make sure that the carriage can move freely across the width of the product. by autoq on May 26, 2012 at 2:45am Add comment Please sign in to comment 0 simply done wothout ordering parts!!!follow the instructions to remove the full module from herehttp://h20000.www2.hp.comthen get Scroll up and click on the plus (+) sign next to cd-rom drive. Hp Officejet H470 Blinking Orange Light Disconnect the power cord from the back of the product.
Solution three: Service the printer If you have completed all the steps listed above and are still experiencing a problem, continue to the Service the printer section at the end of Step one: Replace the tri-color cartridge on the left Follow these steps to replace the tri-color cartridge. With the product turned on, open the cover on the product. Press and hold the Power button (). check over here Remove the power cord and the battery from the printer as well.
If the cartridge is outside of the product for too long, the ink can dry and clog the nozzles. Release the Power button (). After replacing the Ink Service Module I still get an error message and the black ink cartridge light and thepaper feed light flash.Sam by unknown on Nov 23, 2007 at 9:31pm