Home > Hp Laserjet > Hp Laserjet Iip Error 55

Hp Laserjet Iip Error 55

If contacts are ok, replace the high voltage power supply. X represents the error location and can equal one of the following: 1 = Slot number 1 2 = Slot number 2 3 = Slot number 3 6 = Card in Bad FONT cartridge Bad formatter PCB 79 Service All printers This problem can be caused by S/W, drivers, memory (SIMM) PCB's, FONT, Personality and 3rd party I/O options PCB's Replace formatter On the HP II/III printers it can be a loose connector on DC controller see tweaking for instructions on how to repair it. weblink

This kit contains a new fuser assembly, the various rollers for the paper feed path and instructions for installing the lit as well as the instructions for resetting the page count Start typing the address: … CodeTwo Email Clients Outlook How to create built-in UI screens with Adobe XD Video by: Bob When you create an app prototype with Adobe XD, you Look for smooth or cracked worn surfaces. It can also be caused by a defective DC controller.

On the 3Si/4Si a command was sent to print envelopes while the printer was in duplex mode. Remove the card and reseat it, try swapping with a know good card from another printer. LJ4P, 5P Top cover open.

Trying to print envelope in duplex mode (envelopes cannot be duplexed). Subscribe to our monthly newsletter for tech news and trends Membership How it Works Gigs Live Careers Plans and Pricing For Business Become an Expert Resource Center About Us Who We Remove and reseat the optional interface card. In rare instances the ac power supply has failed.

Back back to top How did we do? Check PS501 and PS106 (only on the Laserjet 4100) 13.6 Paper stopped jam at fuser. 13.10 Paper jam in Duplexer. See Service Note 33471-01B if Serial No. https://www.fixyourownprinter.com/posts/1000159 Check to see if fuser bulb turns on.

Suggested Solutions Title # Comments Views Activity Scan-to-Folder to Windows 10 not working (from HP MFP) 3 95 140d Does an HP Network Printer need an IP address to be shared Worn pick up rollers and/or separation pad. Always turn printer power off when removing or inserting cards. Is the computer powered off!

  • Replace the memory chip cable/connector or the DC controller.
  • Error 57 6L/5L Memory card incompatibility - 1,2,4,8 MB, 5 volt, 70 nanosecond or faster 6P/5P/5 Improper main motor function, check gear train for binding.
  • In this case, a firmware recovery DIMM is available.
  • Press continue or go on the printer to clear message.

on LJII short C211 on DC controller PCB to bypass 20 minute delay. How did we do? Also verify the configuration through the menus on the printer. Replace same Replace laser PCB II, IID, III, IIID Replace toner cartridge if defective Inspect fiber optic cable for bare spots, cuts or kinks Replace cable from scanner to DC controller

ERROR 14 No EP Cartridge or No Toner Cartridge No toner cartridge or cartridge not fully seated - pull it out and install it again. have a peek at these guys Extremely heavy or thick paper is also a problem. The line voltage and current source at the printer location might need to be inspected to ensure that they meet the electrical specifications for the printer. Bad registration sensor or bad fuser exit sensor.

Is thereany hope? Other causes include poor quality parallel cables, poor connections, or specific software programs. The error 55 is usually a bad dc controller. check over here If the problem persists and is application specific, verify proper setup with application vendor.

Please try the request again. Power Supply (P/N RG1-0906- 000). If error goes away replace SIMM Replace formatter PCB 5P SIMM malfunction.

Replace High-Voltage Power Supply. 20 ERROR/MEM OVERFLOW/INSUFFICIENT MEMORY 1.

Replace the Fan. Front Door-open Sensor (PS402) broken or stuck. 2. Visually check or replace toner cartridge. 2. Order the HP II/III Service 50 Error Repair Kit Quartz fuser lamp is burned out.

Press Go or Continue. Back back to top How did we do? Bad fuser bulb. 3. http://batteryuniveristy.com/hp-laserjet/hp-laserjet-pro-100-error-54-2.php Back back to top How did we do?

Verify that the tabs aren't damaged and that the tray switches located in the printer are not damaged. X=1: Beam detect malfunction. 2. Back back to top How did we do? Check registration area.

Works great and certainly solved the problem (as I expected it would). -Alan A. LJ4, 4+ Check and reseat laser scanner cable connections Replace laser scanner assembly 4V Check fiber optic cable from scanner to DC controller PCB Replace laser scanner assembly 4L, 4P, 5P Simplify the job by removing font changes etc. Retest.

Reseat the PostScript SIMM and/or replace it. Connect with top rated Experts 19 Experts available now in Live! Check and replace same 68 Error / Service / Cold Reset All printers Temporary error. Is the paper size correct?

Make page less complex and retry. No toner cartridge. 3. Improper MIO connection - look at pins on formatter MIO connection reseat card. The product was delivered just a few minutes ago.

Replace the fan. Bad interlock switch assy LJ4, 4+ Top cover open Bad paper control PCB on ppr feed assy 4L Part of the top door that pushes plunger down is broken Top door Damaged printer I/O port 5P Reseat parallel cable and insure you are using a 1284 compliant bi-directional cable 23 I/O not ready All printers except II, IIP, IIP+, III, 4, 4+, Check the feed and separation rollers in the printer and in the tray.

Check and reseat connectors J4, J5, on the Low Voltage Power Supply, J8, J9, J10 and J15 on DC Control PCA. 2. Replace DC Controller PCA. 3. II, IID Only: 1. 53 Error - Replace memory card. Order the HP 4 Service 50 Error Repair Kit.

© Copyright 2017 batteryuniveristy.com. All rights reserved.