Home > Hp Laserjet > Hp Laserjet Iip Error 12

Hp Laserjet Iip Error 12

Replace high voltage power supply. 4V Bad toner cartridge microswitch SW501 on HV power supply Bad front door open sensor. Remove optional I/O PCA, then re-test. 69.x SERVICE 4000/4050/4100/5000/8000/8100 1. Add to Want to watch this again later? It will not print. check over here

Hooked it up and everything works great. Rating is available when the video has been rented. Respond to this 0 RG1-1604-000CN PC Board : Density adjust board - Includes cable assembly Part number RG1-1604-000CN is used in the following HP products.Product name HP model number(s)LaserJet IIP 33471AB, May require add'l memory 4L Too much data or data too complex, simplify the print job Turn image adapt and page protect to ON or AUTO (Can be set through HP http://www.repairfaq.org/samnew/printfaq/pcfljiipec12.htm

Replace laser PCB II, IID Replace memory PCB III, IIID 53-1 - Error in front memory slot. Just like getting an old girlfriend back. Before replacing components, clean the sensors with compressed air and re-seat their connectors on the DC Controller board. (From: Greg Smith ([email protected]).) Check the 10 uF electrolytic capacitor on the Density Check paper pickup rollers.

Replace Cable, DC Controller to H.V. Replace fuser. OK, things to check: Firstly, there should be a little peg on the cover (on the right hand side under the edge) that goes into a slot on a metal housing No toner cartridge installed External fuser access door not closed.

me). Copyright © 1994-2007, Samuel M. IIISi/4Si Only: 1. Paper Control PCA malfunction. 3.

A second-hand unit could be found somewhere on the Net. (ebay??) Others may want to chip in and give their opinions. The printer door/lid is open. 2. Duplex mechanism has failed 70-71 ERROR 1. Replace Paper Control PCA (Solenoid/Sensor PCB Assembly). 4.

Replace AC Power Module. 3. http://fixyourownprinter.com/posts/47478 Watch Queue Queue __count__/__total__ Solution to HP Laserjet M1005 MFP Scanner Error 12 Meren Daniel SubscribeSubscribedUnsubscribe4949 Loading... Broken separation belt. 2. You can change this preference below.

Conection has been broken between printer and EIO/MIO card; try reseating EIO/MIO card 40.X Mio Error 5Si Only: 40.1 HP Mio port 1 (upper slot) 40.2 HP Mio port 2 (lower check my blog is between 0000J00000 and 2949J2222 2. Check replace SIMM's 61 Service 2686A/D, II, IID, IIP, IIP+, III, IIID, IIIP, 4P Replace formatter PCB 61 Memory IIISi, 4Si, 4V Bad SIMM memory. All printers No toner cartridge installed or not fully seated Is there at least ONE sensitivity tab on the 92295A toner cartridge? 2686A/D Bad cassette microswitch Bad toner cartridge - missing

  1. I'd be more inclined to blame a connector or even a dead fan.
  2. IIP, IIP+, IIIP Only: 1. 53 Error Unit 1 - Replace memory card (top). 2. 53 Error Unit 2 - Replace memory card (bottom).
  3. Press SHIFT+CONTINUE to clear.
  4. Techmoan 104,317 views 10:26 HP Laserjet M1005 - Scanning a Photo - Preview - Duration: 0:46.
  5. Reseat connectors J002 on the DC Controller and J601 on the LaserDrive PCA. 4.
  6. Check and reseat connectors J4, J5, on the Low Voltage Power Supply, J8, J9, J10 and J15 on DC Control PCA. 2.

Hold down the front panel button to display the error LED code. The HP part# for the 200K page IIISi, 4Si maintenance kit is C2062-69001. Check/replace SIMMs. 62.x memory error 4000/4050/4100/5000/8000/8100 only: 62.x where x = Dimm slot, Check/replace DIMMs. 63 SERVICE 1. this content Incompatible memory card in rear slot IIP, IIP+, IIIP 57 error Unit 1 - Incompatible memory in top slot 57 error Unit 2 - Incompatible memory in bottom slot LJ4, 4+,

Remove Dimms, cycle power 4. If you do get 24 V there, then assuming the printer uses the +24 V sensing as the method of detecting when the cover is one, the problem is possibly R817, If you don't get 24 V now, then the problem is almost certainly the microswitch in the LV power supply, or the peg that operates it, or something like that.

III, IIID Only: 1. 53-1 Error in front memory slot. - Replace memory card. 2. 53-2 Error in rear memory slot. - Replace memory card.

I'll proceed as noted and report back. IIP, IIP+, IIIP Only: 1. X=1: Beam detect malfunction. 2. Sign in to add this to Watch Later Add to Loading playlists...

Check SW101 to make sure it is engaged with top cover closed. There is no charge except to cover the costs of copying. Jason Quote:> Anyone know what this means and how I can fix the problem? http://batteryuniveristy.com/hp-laserjet/hp-laserjet-pro-100-error-54-2.php They're all new OEM.

Defective display cable, display, or Formatter PCA. 11 PAPER OUT 1. LJ4, 4+ Plunger missing on top cover. Power Supply (P/N RG1-0906- 000). I may be contacted via the Sci.Electronics.Repair FAQ (www.repairfaq.org) Email Links Page. <> HP LaserJet IIP printer error

II, IID, III, IIID Replace paper control PCB. Love your site---best thing on the web. Inspect PostScript ROMs for bent or broken pins. 2.

© Copyright 2017 batteryuniveristy.com. All rights reserved.