Home > Hp Laserjet > Hp Laserjet 5m Error 51

Hp Laserjet 5m Error 51

We tear apart, rebuild, and test HP LaserJets and LaserJet assemblies all day. Gulbransen 2102 Pacemaker. Turn on, and try to print a test page - which will fail. Troubleshooting Light or Faded Print - HP Laserjet Printers MP Tray 1 Constantly Lifting - HP P3015 Laserjet Printer-Solenoid FixParts and Supplies StoreBrother Parts / Supplies Canon Parts / Supplies Copystar weblink

Replace cable, fuser to DC Controller (P/N RG1-0907-000) II, IID, III, IIID Only: 1. Since we stole this fair and square, and since we have a number of good (but _not_ laser printer) techs around, I'm wondering where we might dig. Replace DC controller. controller. http://www.repairfaq.org/samnew/printfaq/pcfljec51.htm

I think we can eliminate the motor for the moment, as that tends to give Error 52s. If the message persists, contact HP Support. It's not how you play.

  • Same as error 51.
  • Let me explain what that means: The laser beam is reflected off a spinning hexagonal (I think) mirror, and scanned across the drum.
  • Power Supply (P/N RG1-0906- 000).
  • Turn the printer off and turn it on again. 3.
  • Bad engine board.
  • There's a little shutter in the laser beam, opened when a toner cartridge is locked in place - is this opening correctly when you close the printer?
  • Error code Y - No Yellow color HP COLOR LASER PRINTER 8500 1.
  • Control panel 1.
  • Formatter PCA malfunction. 3.
  • Replace the laser/scanner assembly. 5.

Reset printers and cartridge. Open the lower-rear door, and then release one tab. 6. Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations Sometimes just reseating the cable will make this error go away but it will come back eventually. (From: Eric Liber ([email protected]).) Here is the description of the possible 51 errors: 51

Reconnect connectors (J86 and J93) on the DC controller.3. Paper path door open. 2. The one I ran into it was right on the display and the machine wouldn't do anything. their explanation Replace Laser scanner cables from scanner to D.C.

Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. Computer power is off. 23 I/O NOT READY 1. So it looks like it's time to find that new laser printer. Defective laser scanner assembly.

Release one tab. 7.  Rotate the bottom of the rear-door assembly away from the product. 8. http://www.printertechs.com/printer-troubleshooting/hp-error-codes/195-numeric-error-codes-50-59-hp-laserjet Replace the laser/scanner. 53.XY.ZZ PRINTER ERROR There is a memory error with an accessory. Start be reseating the 2 cables (one under the flap) that go to this unit. If your customer complains of the 51.10 error and you can't duplicate the problem then print of the error report in the diagnostic menu or in the same menu go to

Replace the laser/scanner. 4. have a peek at these guys Powered by Blogger. All laser printers have laser/scanner assemblies. Reply 0 0 Pentane Top Student Posts: 5 Member Since: ‎05-08-2013 Message 3 of 10 (19,124 Views) Report Inappropriate Content Re: HP M602 Error - 51.00.10 Options Mark as New Bookmark

Misadjusted or bent Switchback Assembly. Replace Registration Assembly. 5. Defective Paper Control PCA on the Paper Feed Assembly. 4L Only: 1. check over here Register Help Remember Me?

A device error has occurred.2. Note: Inadequate site power can cause this error and is often a result of thunderstorms. 2686 Only: 1. is between 0000J00000 and 2949J2222 2.

Retired Leslies, 147, 145, 760 x 2, 710, 415 x 2.

Replace the laser scanner assembly. 4. III, IIID Only: 1. 53-1 Error in front memory slot. - Replace memory card. 2. 53-2 Error in rear memory slot. - Replace memory card. Lift the cover off of the product to remove it. LOL!

Notify me of new posts by email. Thanks again, for all the support. Or worse, since it was a scrap and not an entire sticker; i.e., I may have found PART OF the inspector's quality control sticker that was on top of the black http://batteryuniveristy.com/hp-laserjet/hp-laserjet-pro-100-error-54-2.php Short the pin closest to the front of the printer. (The printer must be turned off.) II, IID, III, IIID Only: 1.

If the error persists, replace the laser/scanner.Note : Please do not try to perform the above steps if you arenot technically sound. Remove the printer from any UPS supplies, additional power supplies, or power strips. 2. I was surprised to find out that several other people had complained of the same problem. Do not look up this channel - it can output laser light.

Defective wiring harness from the scanner to the dc controller. 4.

© Copyright 2017 batteryuniveristy.com. All rights reserved.