Home > Hp Laserjet > Hp Laserjet 4100 Troubleshooting

Hp Laserjet 4100 Troubleshooting

Contents

Do you wish to proceed to the home page of the new product? Cleaning page instructions Remove all paper from Tray 1. It has to be ordered from HP. top Frequency To ensure good print quality with certain types of paper, use the cleaning page procedure every time the print cartridge is replaced. weblink

by unknown on Nov 9, 2005 at 5:01pm Add comment Please sign in to comment 0 It is either the formatter or the display unit itself which is bad. Please enter a Product Number to complete the request. by schmidtmj1 on Nov 24, 2005 at 7:41am Add comment Please sign in to comment 0 Unfortunately this is one of those difficult errors to diagnose. There are I think two screws to the left you remove and the box should slide straight back. http://h20565.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults/?sp4ts.oid=83436

Hp Laserjet 4100 Manual

I have checked the wire contacts as "Trev Pearson" mentioned and they are making contact just fine. by Anonymous on Dec 8, 2005 at 6:48pm Add comment Please sign in to comment 0 I am working on a LJ 5si that has a blank control panel display. I suppose there is always the first time. What would be the advantages?2) If I try to print complex documents in Indesign CS I get a 49.4C06 Service Error.

Nada. The jetdirect card is a 610N. The flapper also has a padding glued on which is supposed to stop the clickkng noise of the flapper hitting the center of the selenoid. Was the information on this page helpful?

Change your product Change your product Privacy Policy © Copyright 2016 HP Development Company, L.P. Hp Laserjet 4100 Driver I doubt that is the issue. That is only if the fan moves. What is not working is the communication between the engine board and the laser/scanner or that portion of the board which supplies the necessary signals to the laser/scanner are not working.

It is possible if the ecu was defective that it damaged the toner drum by engraving those lines into the drum. Keep getting same message. If you hear the motor turn, have paper in the lower tray and there is a little hole on the left side by the fan grill which you can use a If no luck replace the engine board.

  • The adjacent fusing area might be hot!
  • You will be taken to the Adobe site to download the reader.
  • by unknown on Nov 9, 2005 at 4:28pm Add comment Please sign in to comment 0 Do you hear any noises when you turn it on.
  • when the machie is first turned on it goes through the RAM count and then display's all stars.
  • That's my 2 cents. - Anonymous GET A LIFE, WHO CARES IF IT IS CAPS OR NOT YOU NERD.
  • They may or maynot send you a replacement.

Hp Laserjet 4100 Driver

Why should they have to strain their eyes because someone is too lazy to use the shift key once in awhile? http://h30434.www3.hp.com/t5/LaserJet-Printing/Laserjet-4100-will-not-print/td-p/1301075 I replaced the formatter baord, no go. Hp Laserjet 4100 Manual Press CANCEL JOB to clear the print job from the printer memory. 2. Remove all EIO devices from the printer. 8.

by dmzcompute on Nov 24, 2005 at 8:19am Add comment Please sign in to comment Sorry for the delay in responding - holidays, you know. have a peek at these guys Press the SELECT key. Is this correct?Thanks. I also received the "Close Top Cover" error but only once.

HP had a service note for bad firmware and you may want to call HP Customer Care to see if they still have it and if you can get a replacment Thank you for all your help on this. - Anonymous 0 Thanks I will try that. First time it happened, I totally messed up troubleshooting it since I pulled the formatter and JetDirect card, but the error was resident in the controller and since I work pretty check over here Anyone concur? (BTW--the milligrams could refer to the amount of aspirin needed to deal with this mess.) by dstal on Mar 13, 2006 at 6:56am Add comment Please sign in to

ideas? Upon being turned back on the computer installed a Windows update before allowing full login. Country of purchase* Select Country of Purchase AfghanistanAlbaniaAlgeriaAmerican SamoaAngolaAnguillaAntigua and BarbudaArgentinaArmeniaArubaAustraliaAustriaAzerbaijanBahamasBahrainBangladeshBarbadosBelarusBelgiumBelizeBeninBermudaBhutanBoliviaBosnia and HerzegovinaBotswanaBrazilBritish Indian Ocean TerritoryBrunei DarussalamBulgariaBurkina FasoBurundiCambodiaCameroonCanadaCape VerdeCayman IslandsCentral African RepublicChadChileChinaChristmas IslandCocos (Keeling) IslandsColombiaComorosCook IslandsCosta RicaCote D'ivoireCroatiaCyprusCzech RepublicDenmarkDjiboutiDomincaDominican RepublicEcuadorEgyptEl SalvadorEquatorial

by Anonymous on Dec 8, 2005 at 6:50pm Add comment Please sign in to comment 0 I have a networked Laserjet 4100.

Over time the padding wears away and all that is left is the glue which causes the flapper to stick to the selenoid and not release. Note: Use the most current version of the reader for viewing these PDF user guides by clicking the "Adobe" link below. IF I SWITCH OFF AND ON THE MESSAGE STILL APPEARS. Then make sure the job calls for the type of paper specified in the other tray.

Even if the display is blank the motor should turn. Search all support All Support Software, Drivers and Updates Troubleshooting How to Product Information User Guides Cancel Example: “Laserjet P1102w driver” or “HP Pavilion 17-f002na will not turn on” Loading Results Any guesses? this content Not sure exactly which menu it under, could be "PAPER HANDLING" or something like that?

CAN U ADVISE ON WHAT I CAN DO NEXT. This product has been successfully added to your profile. by JMUKHOWA on Jan 17, 2005 at 11:15pm Add comment Please sign in to comment -1 I'm confused about this part "I removed the formatter, and the engine test page still This morning the computer was turned on (everything worked properly the last time it was used) and I tried to print a document.

© Copyright 2017 batteryuniveristy.com. All rights reserved.