Home > Hp Laserjet > Hp Laserjet 4 Error Code 51

Hp Laserjet 4 Error Code 51

A device error has occurred.2. Verify stable power >110V AC (If fuser is replaced and printer is powered up without a 20 minute wait the error code 50 will be redisplayed) 2686A/A Bad 47ohm resistor on Replace laser scanner ass'y.3. HP LASER PRINTERS 4, 4+, 5 1. http://batteryuniveristy.com/hp-laserjet/hp-laserjet-error-code-13-0000.php

Turn the printer off, and then turn the printer on. 2. Replace the fan. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize2. If the error persists, replace the main motor.

S.E.R. Try connecting the product to a different power source or surge protector.4. Organ Items On eBay RSS Classified Feeds On The Internet Classified Archives Buy & Sell Church & Classic Organs Archive Buy & Sell Theatre Organs Archive Buy & Sell Hammond and If not, we'll debug that.

  1. Replace DC controller board.
  2. Cycle power on printer Bad formatter PCB 67 Memory IIISi, 4Si, 4V Bad SIMM memory.
  3. Paper tray empty or not seated correctly. 2.
  4. Short C202 on the DC controller PCB to bypass the 20 minute delay, power printer OFF!!) 4V, 4L, 4P, 5P Verify fuser is properly seated Replace fuser 51 Error (Loss of

SHIFT+CONTINUE to continue printing Temporary error. Replace the scanner ass'y HP LASER PRINTER 5200 1. x = 1: Beam detect malfunction x = 2: Laser malfunction Required Action Press SELECT to resume operation. Replace the formatter and/or firmware DIMM. 4.

Defective laser scanner assembly.2. Replace memory PCB 53-2 - Error in rear memory slot. Replace the engine controller board. 5. Source Today: I turned the printer on to print.

I think what you found was the inspector's quality control sticker that was on top of the black box. -- SP (Lamar) Rodgers W5000, Conn 643 Thomas Trianon stripped to be It's simply shared in Windows.) -- SP (Lamar) Rodgers W5000, Conn 643 Thomas Trianon stripped to be MIDI project organ 65 Hammond E-112, 73 T-582C, 59 M-3 Reply With Quote 01-27-2015,01:19 When replacing the scanner make sure the shutter control arm on the left front side of the scanner is sttached correctly so that the shutter closes when the toner cartiridge is Try connecting the product to a different power source or surge protector. 6.

Kimball something-or-other. http://www.advancedlaser-hp-error-codes.com/error_51.htm Press the SELECT button to continue or press ? HP LASER PRINTER 4V 1. Problem with fiber optic cable. 3.

Check the cable connections between the laser/scanner and the ECU. 3. have a peek at these guys HP LASER PRINTERS 5000, 5100 1. The product has experienced an internal hardware error. 2. Create your Spare Parts List.

Put your IR sensor on the end of that and test again. HP LASER PRINTER 3050, 3052, 3055, 3390, 3392 1. Remove all the cables from the scanner retaining clips. check over here Replace the ECU.

If the error persists, replace the laser/scanner.Note : Please do not try to perform the above steps if you arenot technically sound. If the message persists, contact HP Support. Turn the printer off and then on. 3.

I am only a channeler of information and DO NOT service laser printers.

LJ4 Bad output rollers (See service note C2001-03) 500 sheet lower cassette not properly adjusted. (See service note C2001-01) LJ4, 4+ Rear door open. The page containing the error will automatically be reprinted. 2. Replace DC Controller. IIISi/4Si Only: Visually check or replace toner cartridge. Short capacitor CP005 on DC controller PCB to bypass 20 minute delay, power printer OFF) LJ4, 4+ Replace fuser. (Note!!

One of my students bought a scanner and laser printer combined last year, perfect for copying a page or two of music to avoid page turns. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 51.X PRINTER ERROR A loss of beam-detect If the error persists, replace the laser/scanner.HP LASER PRINTER 3300, 33801. this content You would need to find an old hp 4 no longer working and switch the laser/scanner.

Not one of them had a bad connection and it was always replacing the laser/scanner or lubing the motor within the laser/scanner that got the printer working again. Turn on, and try to print a test page - which will fail. Check I/O and replace if req'd 24 Job memory full Add more internal printer memory or simplify the print job 25 xxx Mem full All printers Add more internal printer memory

© Copyright 2017 batteryuniveristy.com. All rights reserved.