Home > Hp Laserjet > Hp Laserjet 4 Error 57

Hp Laserjet 4 Error 57

Question about HP LaserJet Printers & Copiers 2 Answers Color Cartridge Failure ...57 Left slot Verify that the packing tape has been removed from the cartridges. Where are these cards located? Replaced the Main Motor: no change. Replace the fan. his comment is here

Thanks, [email protected] 732-267-4065 cell Have had the same problem. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 55.xx PRINTER ERROR alternates with CYCLE POWER Check the main motor’s cable to ensure that it is seated properly. 4. the motor sometimes passes the self test, and I can rotate it by hand.

For 50 FUSER persistent messages, manual says: Replace the following components in the order given: 1. Replace the engine controller board. 5. Do I have to order the entire optput assembly?] Reply With Quote Quick Navigation Hewlett Packard Laserjets Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums

  • First Time Here?
  • Turn the printer off, and then turn the printer on. 2.
  • Check the fan’s connector and make sure the fan is not blocked. 2.
  • HP 56 vs. 45 & 57 vs. 78 Inks 5 post • Page:1 of 1 All times are UTC Board index Spam Report ERROR The requested URL could not be retrieved
  • We tear apart, rebuild, and test HP LaserJets and LaserJet assemblies all day.
  • by moe on Aug 10, 2005 at 9:37am Add comment Please sign in to comment 0 Card is in the back, held in by 2 screws.
  • Videos English Open Menu English Deutsch Español Français Português 中文 한국어 † The opinions expressed above are the personal opinions of the authors, not of HP.
  • Question about HP Printers & Copiers 1 Answer 4110 officejet series all-in-one error message ...57 or HP #28) goes on the left side.

It starting doing that after I installed a jetdirect internal print server in it. I re-installed the old fuser and still got 57 SERVICE code. Printer will work fine without it. Press GO.

You can print your Parts List or export to Excel to further work with him. If it is not within the proper range, replace the fuser. by unknown on Mar 27, 2003 at 8:49pm Add comment Please sign in to comment Please sign in to comment HP LaserJet 4 Buy discount ink Buy this printer More HP Before this, the motor would only run for about one second before it would hang and give 57 SERVICE.

Check the printer’s configuration. 3. I would then replace the low voltage ac power supply then the formatter. For 57 SERVICE message manual says: Main Motor Functional Checks Inspect the gear train for debris that would block the free operation of the gears. Check the gears in The page containing the error will automatically be reprinted. 1.

Plug the printer into a wall outlet and see if this resolves the problem. 3. http://h30434.www3.hp.com/t5/Inkjet-Printing/Main-motor-choice-to-solve-a-Laserjet-4-57-Service-error/td-p/4081954 Results 1 to 3 of 3 Thread: LaserJet 4: 57 Service & 57 Fuser Messages Thread Tools Show Printable Version Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode Serving Northern *ia, USA Voice 703-450-0302 http://www.veryComputer.com/ Top 1. Showing results for  Search instead for  Do you mean  or Post new question Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this

Reply With Quote 08-22-2009,03:59 PM #3 sinbad View Profile View Forum Posts View Blog Entries View Articles Junior Member Join Date Aug 2009 Posts 2 With new fuser already installed, I this content or it's affiliates. I seen the post about a bad MIO card or J2550 card. and may not be used without advance written permission of PrinterTechs.com, Inc.

Word Pro Default Font for Text Files 5. If the error persists, replace the engine controller board. 59.X PRINTER ERROR A main motor error occurred. Try replacing the fuser.) 56.X PRINTER ERROR An incompatible combination of input/ output bins was selected. http://batteryuniveristy.com/hp-laserjet/hp-laserjet-pro-100-error-54-2.php It none of the above, the next item would be the main motor itself.

Let me know if it does. Replace the formatter board.   (On the 5si, 8000, 8100 this could be a fuser problem. With fuser out, I powered up, depressed the rear door latch sensor and the motor ran for about five seconds -- as it would in a normal self test but

Check the power at the customer’s location. 2.

Try the DIMM in another slot. (The firmware DIMM must remain in slot #4—the lowest DIMM slot.) 3. After doing all the above, I did another power on self test and got a 57 SERVICE message so it is going back and forth between 57 SERVICE and 50 If the printer is already plugged into a wall outlet, try another power source in the building that is independent of the one currently being used. 4. I am looking in particular for the error code 57 > on an HP laser jet 4.

Priming HP 57 cartridge? 12. Structural Testing Items 9. The only thing that I did was disconnect the printer because I had to switch offices. check over here by moe on Oct 3, 2008 at 8:39am Add comment Please sign in to comment 0 Thank you Moe...it's working now.

We have no manual. The page containing the error will automatically be reprinted. 2. Articles Forum New Posts FAQ Calendar Community Groups Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Who's Online Blogs Advanced Search Forum Printer Forums Hewlett Packard Laserjets Sign Up Login Add Question unknown asked Mar 26, 2003 at 12:47pm 0 HP LaserJet 4 HP 4 service error 57 I have purchased and installed the PCA motor kit to

If you can turn the motor 15-20 times without encountering much resistance and it turns smoothly, I would guess that you don;t have a bind in the gears. If there is not continuity between the fuser connectors neutral and hot with the fuser removed, replace the fuser. Are there any other functional parts associated with this code? Top HP laserjet 4 error code 57 by Mitch Pilchu » Sun, 25 Jul 1999 04:00:00 57=main motor not functioning properly.

I am looking in particular for the error code 57 on an HP > laser jet 4. > Thanks, > Robert -- Mitch Pilchuk Pilchuk Laser Printer Repair Now tried various configuration with fuser out, or toner cart. Press GO. The Main Motor drives all ...

Replaced the DC controller board: no change. While I can find sources for a replacement RH7-1151, an Internet search for RH7-1153 turns up nothing.Can anyone tell me if these two part numbers refer to the same motor, i.e. I've been looking for one for parts. Respond to this 0 MARV: A "57 Service Error" on a HP 4 does indicates that there was a general motor failure, or a RELATED PROBLEM...The FORMATTER detects a main motor

Turn the gear on the top of the fuser and see if it will turn. Our quality is highly regarded due to our constant testing and attention to detail.We sell a wide variety of maintenance kits and parts, meticulously refurbished printers, and high-quality toner cartridges. Your cache administrator is webmaster. If ...

Nothing seems to effect the error message. A rotating fan indicates that the +5 VDC and +24A VDC voltages are present. (The fan runs on +24A VDC. We Laserjet 4 printer: 57 SERVICE ERROR message. We help people fix printers.

© Copyright 2017 batteryuniveristy.com. All rights reserved.