Do you ever get the error when you do lets say a 50 or 100 page paper path test from the printer. Description The printer received more data than can fit in its available memory. top 13.12.08/13.12.09, 13.12.10/13.12.11 JAM IN OUTPUT DEVICE Description Jam in the output device (stapler stacker of stacker). Figure 6: Replacing the entrance cover and closing Tray 1 Reinstall the print cartridge and close the top cover. his comment is here
Remove all memory DIMMs or third-party DIMMs from the printer. (See the printer User's Guide for information about removing DIMMs.) Remove all EIO devices from the printer. (See the printer User's by unknown on Jan 16, 2006 at 8:39am Add comment Please sign in to comment The problem is finding the part number for the memory chipcable and contact assembly. top Additional information To print a configuration page at the control panel Press (Select) to open the menus. by DavidMaurice on Apr 16, 2009 at 10:39am Add comment Please sign in to comment 0 If I understand this correctly you are saying that by backing up to the OLDER http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422
Figure 8: Sliding the tray out If the edge of the jammed paper is visible in the feed area, slowly pull the paper down and out of the printer. (Do not This cleans up the permanent storage by removing old areas that are not being used. Make sure you have the correct part numbers for the printer model.
Action Turn the printer power off and then turn the printer power on. X Description 1- Beam-detect error 2- Laser error Action Press the (Select) button to continue. Figure 39: Removing the jammed paper Push the fuser firmly into the printer until the blue levers on both sides click into place. 13.20.00 Jam In Tray 2 Hp 4015 Questions?
by Trev Pearson on Aug 8, 2005 at 11:48am Add comment Please sign in to comment 0 Try searching the forum using that error code. Hp Laserjet 4250 Error Codes If other error messages persist, replace the stacker or stapler/stacker. All I had to do was press pause/resume, cancel and the tick button at the same time and it recognised it as a non-hp cartridge and started working. Loading
Pressing the Select (check) button should clear the message. Hp Laserjet 4200 Cartridge Installed Message replaced dc controller PCA4. Look for a jam in another location, contact HP, or contact an authorized service agent. Figure 51: Closing DIMM access door Set the bottom of the cover onto the printer.
Open and close the top cover to clear the message. http://www.printertechs.com/printer-troubleshooting/370-13-20-error-on-hp-laserjet-4200-or-hp-laserjet-4300-series I have noticed that only certain jobs that are sent to the printer result in this error.Still working on it. Hp Laserjet 4250 Error 13.20.00 Jam In Tray 2 What is this error and what can you do about it? Hp Laserjet 4200 Error Codes Model...
Figure 27: Removing paper Verify the deflector in the printer is working correctly. http://batteryuniveristy.com/hp-laserjet/hp-error-e8.php This document explains the message types, it lists and explains the numbered error messages, and provides recommended actions for resolving problems. first, there is no duplexer being used. Knowing the issue has not solved it for us, other than to tell people to reformat their documents and be rid of the bad fonts. - unknown 0 Hi,We had this Hp Laserjet 4250 Error 13.01.00 Jam In Tray 2
Turn off printer power. Swap out the Formatter.Sorry, I didn't pick up the fact you have a Service Manual already.My gut says, duff Netcard.Trev by Trev Pearson on Aug 8, 2005 at 12:36pm Add comment Figure 35: Removing the optional duplexer, if installed Open the rear output bin and pull the extension outward until it stops. http://batteryuniveristy.com/hp-laserjet/hp-laserjet-4200-errors.php If the above action does not solve the issue, contact HP or authorized service provider.
Figure 58: Loading paper Make sure that the stack is flat at all four corners and that the top of the stack is below the maximum-height indicators. top top 40 EIO X BAD TRANSMISSION To continue press (Select) Description The connection has been broken abnormally between the printer and the EIO card (HP Jetdirect card) in the specified Warranty status:Unspecified Check warranty status Enter product serial number The serial number you entered,, matches a different product than the current product. Hp Laserjet 4200 And 4300 Series Printers Drivers An improper communications protocol might be in use.
This is typically an e-label issue. Action Press the (Select) button to continue. Remove the print cartridge and check the paper path for paper. http://batteryuniveristy.com/hp-laserjet/hp-mfp-error-49.php This error indicates a problem with the lifting of the paper stack Tray 2.
We just used remote desktop to delete that font off everyone's laptops and this error pops up less now. top Handling persistent messages If a message persists requesting that a tray be loaded, or if a message indicates that a previous print job is still in the printer memory, press Replace theDC controller PCA. The part number is RM1-0034-000.
Figure 33: Opening and closing the top cover If a jam message persists, it is possible that jammed paper is still in the printer. You might damage the fuser. If a duplexer is installed, remove it from the back of the printer. I have an HP 4200 (Q2428A) with 3 trays and stapler.
Turn the power on. If the error persists contact HP or an authorized service provider. Restart. first, there is no duplexer being used.2.
The ON setting causes the message to appear on the printer control panel display, and the printer goes offline for 10 seconds, before returning online if an error occurs that prevents If necessary, lift the black plastic guide that is located on the top of the fuser to gain access to the jammed paper. You’re Not The Only One… After powering on your HP LaserJet 42xx/43xx, you get Error 60.2 displayed on the control panel. Figure 48: Opening DIMM access door Remove the DIMM from the antistatic package.
top Provide feedback Please rate the information on this page to help us improve our content. top 59.4 EP MOTOR ROTATION ERROR (HP LaserJet 4300 only) Description The print-cartridge drive motor (HP LaserJet 4300 only) is not functioning properly.