Home > Hp Laserjet > Hp 4100 Error Messages

Hp 4100 Error Messages

Contents

Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers by dmzcompute on Feb 9, 2005 at 2:43pm Add comment Please sign in to comment lmao lmao! - Anonymous Learn how to read and follow posts; your name is hereby changed by dmzcompute on Jan 21, 2007 at 8:02am Add comment Please sign in to comment 0 DMZ,I loosened the assembly with the 2 contacts on my 4100 and tried it...The printer Locate the cartridge selection number on the cartridge label. http://batteryuniveristy.com/hp-laserjet/hp-4100-error-message.php

Figure 79: Open the cartridge access door Press lightly on the top of the cartridge that you are removing to release it from its slot. Step three: Replace the USB cable Securely connect an alternate USB cable to the product. If the product does not turn off, continue to the next solution. Do I shotgun it and start ordering parts and replacing parts (flash,formater,engine pcb) not knowing if those parts will fix it or do I just go to Ebay where I can

Hp Laserjet 4100 Manual

We actually have 2 of these printers in-house and I can "borrow" the formatter. If these steps resolved the issue, you do not need to continue troubleshooting. Complete madness I tell ya! Figure 14: Lower the paper tray, Fold out the tray extender, and then flip up the paper stop NOTE: For best results when loading legal-size paper, fold in the paper tray

  1. Remove all EIO devices from the printer. 8.
  2. Privacy Policy Terms of Use Sign Up Login Add Question dekuda asked Jan 19, 2007 at 2:58pm 0 HP LaserJet 4100 HP Laserjet 4100 54.1 error I have decided to open
  3. The carriage might move to the center of the product.
  4. Press firmly on the overlay to ensure proper installation of the overlay adhesive or pins.
  5. If you cannot cancel the task, press and hold the Power button () for three seconds to turn off the product.
  6. I work in a library and hate wasting paper.
  7. Do not use a power strip or surge protector.
  8. That's my 2 cents. - Anonymous GET A LIFE, WHO CARES IF IT IS CAPS OR NOT YOU NERD.
  9. Solution three: Reset the All-in-One Follow these steps to reset the product.
  10. If sit doesn't see the voltage, it will give the error message.

Check the paper feed rollers on the rear access door to make sure that they are clean, free of paper bits, and rotate freely. If the problem requires me to replace any type of boards in the printer can someone please e-mail me instructions. Make sure you do it with power off on both printers. That is only if the fan moves.

hope this helps. If printing on an envelope, the edges of the envelope are bent. Close the cartridge access door. I broke part of the black plastic piece that conrols the "output bin full" sensor and I had to superglue it back together.

Please wait while we process your request. by moe on Mar 13, 2006 at 11:35am Add comment Please sign in to comment 0 Another one of those 4100 series printers (4101MFP) with a dead display (no control lights Parallel cable, network cable, etc. BTW, putting the cartridge in the 4000 and running some pages won't affect the chip since the 4000 doesn't have any means of writing to it.

Hp Laserjet 4100 Driver

You can see the lines that are printed on each page. http://www.printertechs.com/printer-troubleshooting/hp-error-codes Figure 6: Disconnect the power cord Unplug the power cord from the wall outlet. Hp Laserjet 4100 Manual I don't hear the engine come on when it is turned on. Replace a DIMM or EIO device if you determine that it causes the error. 11.

but none for the 4100. check over here by unknown on Jun 9, 2006 at 12:28pm Add comment Please sign in to comment 3 When my HP 4100 runs out of paper in one tray it automatically starts pulling by moe on Jan 27, 2007 at 10:33am Add comment Please sign in to comment 0 Good luck had the same problem with a 4345 mfp replaced boards checked connections etc ie - no link lights on the jetdirect, no harddisk spin up...

You wouldn't have any other 4100s around you could borrow the firmware chip from, would you? NOTE: If Save is unavailable, make sure that there is a name for the setting in the Name box. If the issue persists, continue to the next solution. his comment is here Any & all advice welcome.

It's also not a cheap part. Press the Power button () to turn on the product. Figure 39: Insert the cartridge Firmly push the cartridge in until it snaps into place.

What you need to do is get a used or empty 4100 toner cartridge and try it.

Look inside the product to see where the carriage is stuck, and then check for any torn paper or objects that might be restricting the carriage. NOTE: HP cannot guarantee the quality of refilled or remanufactured cartridges. If the product completes the job normally, there is no need to continue troubleshooting. You should wait about 10 minutes without power for the error to clear.

Figure 80: Remove the cartridge by pressing down to release it 1 - The color cartridge belongs in the slot on the left 2 - The black cartridge belongs in the Securely reconnect the USB cable to the rear of the computer. If sit doesn't see the voltage, it will give the error message. weblink any ideas?

It has to be ordered from HP. Check the lights on the control panel to make sure that they are no longer blinking. One is to take one of the 4050 formatters and try it in the 4100 it may or may not work. Press and hold the Cancel button (), and then press the Start Color Copy button ().

Call 1-800-227-8164, follow the prompts to HP Tech support, when you get asked what the model of the equipment is answer JetDirect 615N. I am not sure at all what is supposed to happen when i do that, but what I get is a page full of black vertical lines, spaced exactly as they I stuck some cardboard in the sealing strip slot on our 4200. One thing you mention which is interesting.

Load the alignment page print side down on the scanner glass. by Stephen on Nov 15, 2006 at 6:53pm Add comment Please sign in to comment 0 Does anyone know what I need to change so that my email from outlook web As to the firmware, call hp customer care and tella them you are having a problem with 49 errors and someone told you there is a service note on the firmware by unknown on Feb 8, 2005 at 11:06am Add comment Please sign in to comment 0 Miguel,The only place of know of is from HP directly or from parts places which

Recommendations? If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and back on as you install each device.

© Copyright 2017 batteryuniveristy.com. All rights reserved.