The funny thing is, when I first turn the printer on, it says checking printer, and spits out about 4 or 5 blank pages, and then jams. That was the problem. This content is provided “AS IS” and is subject to change or removal at any time. This problem can be caused by software/drivers, memory PCA's, font macro personality cartridges, or optional I/O cards. 2. navigate here
Sounds like the solenoid might be the problem. Fast on-site 4050 printer repair with numerical error codes in Los Angeles and Orange County! laserjet 4050 printer 90015 Downtown L.A. 4050 printer repair 90016 Downtown L.A. (City of LA) 90017 Downtown L.A. (City of LA) 90021 Downtown L.A. (City of LA) 90041 Eagle Rock (City Turn the printer off, wait 10 minutes, and then turn the printer on. 2.
Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers Replace PS1 if defective. 2. Replace toner cartridge. 2. If there is no glue, why would it stick?Thanks again - it is nice to see a familiar name (you helped me get fusers to repair printers in the past). -
Troubleshoot a problem Help Other Knowledge Base options Search HP Support Center Top issues Most viewed solutions Advisories, bulletins & notices Manuals Setup & install Learn & use Perform maintenance Upgrade X = description: 1 = Illegal input or bad accessory connector 2 - Illegal output The page containing the error will automatically be reprinted. 1. If error does not reappear, replace RAM expansion card. 3. Any suggestion guys??Thanks by krazius on Aug 12, 2005 at 7:18am Add comment Please sign in to comment 0 If you have a re-occuring 41.5 error, I have found thatreplacing the
If I pull the tray out, before turning it on, it goes to "offline" I can then put the tray back in, and get to "Ready" I can try to print, Hp Laserjet 4050 Driver On older style printers this is often caused by a bad main motor. (Older style printer being printers with halogen heating elements in the fuser - 4, 4+, 5, 4si, 5si, We don't sell hard drives, monitors, software, mp3 players, or the zillions of other computer products sold by every other cookie-cutter website. http://www.printertechs.com/printer-troubleshooting/hp-error-codes/195-numeric-error-codes-50-59-hp-laserjet If you cannot find your product on this site, go to HP Support Center - Hewlett Packard Enterprise.
Same as error 51. 2686/D Only: 1. by krazius on Aug 14, 2005 at 5:24am Add comment Please sign in to comment 0 I read all your posts, check all the sensors, replace the feed assy behind tray When print double on manual tray 41.5 comes out. X HP 4050 PRINTER ERROR a loss of beam detects occurred.
by unknown on Apr 16, 2008 at 1:00pm Add comment Please sign in to comment 0 Lots of great info. https://www.orionmarket.com/product_error_page/HP/HP-4050/ Computer and printer may be set to different baud rates. 2. Hp Laserjet 4050 Troubleshooting Note IIISi/4Si: Short cp005 on DC Controller to bypass Error 50 time delay. (The printer must be turned off.) 5Si/4000/4050/4100/5000/8000/8100 Only: The fuser is malfunctioning. 50.1 Fuser low temperature failure. 50.2 This is due to the many different formatter board revisions.
The tech simply pushed the roller back onto it's drive wheel. check over here IIISi/4Si Only: 1. Turn the printer off, and then turn the printer on. 2. IIP, IIP+, IIIP Only: 1. 57 Error Unit 1 - Incompatible memory card in top slot. 2. 57 Error Unit 2 - Incompatible memory card in bottom slot. 57.x ERROR (IIISi/4Si
IIISi/4Si Only: 1. It was nice to get this 4000 back in business. Replace Formatter PCA. 3. http://batteryuniveristy.com/hp-laserjet/hp-4050-error-codes.php Press the clip, swing the plastic back on its hinge.
Remove the top cover and looking from the front on the right side of the output bin is the sensor and the flag will be attached to the black post which You may want to remove the roller and then remove the clutch whcih sits behind it. Reset by pressing the continue key. 2.
I press GO to continue, but only a blank page prints. Round 2 - I took everything apart, then I inspected and cleaned all the rollers (rubber and plastic). http://www.fixyourownprinter.com/kits/hp/K41The solenoids have to have a pad to dampen the noise and prevent residual magnetism from holding the plates down. Our librarian had paid for two service calls for the 41.5 error and nothing had worked.
The printer passes the paper path tests for all paper trays. Best of all we have the technical ability to provide LaserJet 4050 printer repair on the first visit. If that does not work, replace the fuser. weblink Seems the clutch on the assembly will sometimes fail to engage, causing a 41.5Part # RG5-2651-090CNBagger by Bagger on Aug 12, 2005 at 8:23am Add comment Please sign in to comment
Made my work easier :) by unknown on Nov 6, 2008 at 2:19am Add comment Please sign in to comment 0 Hi, having the same 41.5 problem.The 41.5 is only occuring In all the time I've serviced 4000 and 4100 (4200's and up are different with a 3rd roller rather than the half round shoes) printers the most I;ve done is clean Computer is powered off. 3. Paper Control PCA malfunction. 4V/4MV Only: 1.
Fast onsite Laser Jet 4000, 4050, 4100 printer repair with 13.05.00 paper jam service error We specialize on LaserJet 4200, 4300, 4240, 4250 and 4350 printer repair with 13.05.00 the error HP LaserJet 4050tn C4254A 16 MB RAM (8 MB internal); HP Jet direct print server card (J3113A) for connecting to a network; one 100-sheet multi-purpose tray (Tray 1); one 250-sheet tray