Home > Hp Error > Hp Error 55.a

Hp Error 55.a

On the 5L, set the Enhanced I/O to AUTO (PCL mode) and resend the print job. Just remove the menu display and the remove the top cover and you will see the fan on the left side. Verify that the SIMMS or memory cards are seated. Tell us some more! his comment is here

Replace this as an assembly. Turn the printer off, and then turn the printer on. 2. Check I/O Cable, it could be the wrong cable or damaged. The code 55.A will appear when the fuser and duplex can't work with eachother.

The D.C. If the message still persists, replace the formatter. I will be glad to assist you in this issue. flipfloppity posted Aug 14, 2016 Upgrade mobo but keep cpu and...

Replace the ECU. 4. I/O configuration for the computer or printer is incorrect. Posted on Jan 29, 2009 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images DLYNAUGH 1 Answer SOURCE: HP Business Jet If there is not continuity between the fuser connectors neutral and hot with the fuser removed, replace the fuser.

Unplug Power Cord Hold POWER and RESUME buttons Plug in Power Cord Release buttons after the printers starts up Hold CARTRIDGE and RESUME Press POWER Release all buttons after the beeps Check pickup rollers and separation pad clean as needed. Replace the fan. Back back to top How did we do?

Or just drag it here! I bet it tells you which part is going out. Reinstall the toner cartridge and close the top cover. 54.4 PRINTER ERROR alternates with CYCLE POWER TO CONTINUE A problem exists with the customer’s line voltage. 1. Perform an engine test. 4.

Defective formatter board. 3. http://www.fixyourownprinter.com/posts/4942 Paulus if it worked for you great thats what this site is about sometimes new fresh look at old problems. IIISi/4Si check the door open sensor flag, PS1. You could sign on and give advice as there are no tests or qualifications to do so.

ERROR 14 No EP Cartridge or No Toner Cartridge No toner cartridge or cartridge not fully seated - pull it out and install it again. this content In your case it seems as if a prntjob had corrupted the internal memory of the printer. When I plugged in the power cord the printer started and did about a 5 minute maintenance procedure and now works fine. How about the I/O port - damaged, seated properly, pins not bent? 4+/5P/5 The computer and printer aren't talking because of improper signal protocols.

Replace the formatter board. 4. Printer Works RM1 9371 000 DC Controller As M775 mfp HP LaserJet DC Controller For M775 Printer RM1 8898 - USD70+shipping Mar 18, 2016 | HP LaserJet M775DN Laser Multifunction... 1 Then put the printer back online and send a test job from the host computer via the parallel cable. weblink While I'm here, I'd like to thank you for all your previous informative posts about the HP 8000DN.

If the message persists, replace the ECU.4. Defective MIO Card - Replace card Defective Formatter Card - Replace card Back back to top How did we do? To check the fuser, turn the printer off and remove the fuser.

Caution needs to be used when installing the new assembly - be careful of the sensor flag spring! 5Si - Can be caused by field replaceable units (FRU's) not installed correctly.

  • Plug the printer directly into the wall. 4.
  • You can verify this by substituting a known good DC controller if possible.
  • Print a page and open the cover after it printed but before the fuser and see what the image looks like.
  • Technicians answer the phone and help customers with printer problems.
  • ERROR 50.XXXX - ERROR 51 (Loss of beam detect) This is a beam detect error indicating a problem with the laser scanner.
  • Video Photos Link Add Upload Upload × × Draw a box over the problem!!
  • Please click the thumbs up button to say "Thanks!"Clicking "Accept as Solution" on a reply that solves your problem makes it easier for other people to find solutions.I am an HP

or it's affiliates. Replace the laser/scanner. 5. X = Description 4 Printer Fan 7 Duplex Fan 1. controller board.

HP LASER PRINTERS 5SI, 8000, 8100, 8150 1. Los Altos Hills, CA Thank you. Replace the formatter board.2.Replace the D.C. http://batteryuniveristy.com/hp-error/hp-error-405-fax.php Perform a service test. 5.

I just purchased a Continuous ink system for it and tried to install it. Click "Add" to insert your video. I really wouldnt reccomend the above thread you can do more damage than good. Power cycle the printer.

Look for "working pull from damaged unit". Error 55 On IIISi/4Si Printers this is due to the DC controller not receiving the proper information upon startup. Replace or clean as needed. Verify that the flat ribbon cable between the ECU and the formatter PCA is connected correctly.4.

© Copyright 2017 batteryuniveristy.com. All rights reserved.