This is caused by the HPLIP hp: backend, since switching the connection to AppSocket/HP JetDirect (socket:) works. On the LJ4/4M/4+/4M+ the sensor flag can get knocked out of place when a paper jam occurs and the tray is pulled out abruptly. May require add'l memory 4L Too much data or data too complex, simplify the print job Turn image adapt and page protect to ON or AUTO (Can be set through HP Bad interlock switch assy LJ4, 4+ Top cover open Bad paper control PCB on ppr feed assy 4L Part of the top door that pushes plunger down is broken Top door weblink
IIISi/4Si check the door open sensor flag, PS1. In this case, a firmware recovery DIMM is available. Check I/O Cable, it could be the wrong cable or damaged. Turn printer off and unplug power cord and reseat the EIO card or the network card.HP LASER PRINTER P30051. http://www.advancedlaser-hp-error-codes.com/error_40.htm
summary: - Error while printing with HP Laserjet: 40 EIO Transmission Error+ Error while printing with HP Laserjet: 40 EIO Transmission Error with hp+ backend Changed in hplip (Ubuntu): status: New Replace if necessary. Error 18 MIO Not Ready The printer is not connected to a LAN when it's expecting to see a LAN. All this using HP LaserJet 4100 Series v3010.107 postscript [en] (recommended) On the other hand, all works correctly when using HP LaserJet 4100 Series Foomatic/ljet4 [en] sdowney717 (sdowney717) wrote on 2010-04-06:
If all else fails, simplify the print job and print manageable segments at a time. 21 PAGE TOO COMPLEX The data (dense text, rules, raster or vector graphics) sent to the Remove and reseat the optional interface card. Replace main motor. This may be a residual error from those days, or might be invoked when a network link descends to chaos. 40 EIO X BAD TRANSMISSION Any communication link can fail.
This type of error can be caused by invalid print commands, corrupt data, or invalid operations. Curiously, HP forums are often missing from the results. PS402 on front door PCA under transfer roller Bad DC controller PCB 16 Toner low All printers Toner uneven in cartridge Bad toner cartridge contact points Replace high voltage power supply. I will have purchasing call in an order.
Remove and reinstall the supply, replace the supply. On the IIP/IIIP this can be caused by a defective toner cartridge, defective cooling fan, PS4 or PS5 sensors. 40 Eio Bad Transmission Error On EX engine printers this error is caused by a bad PIU (paper input unit). 41.x PRINTER ERROR A temporary printing error has occurred. Replace or clean as needed.
manualslib offering a dreadfully clunky way to read a user guide. have a peek at these guys If this is the case I would try to flash firmware straight to the printer from a laptop off the network. The printer required a firmware update. If all that is right and the error persist.
The connection between the printer and the EIO card is bad. 2. Is the software set for the size you're using? Watch the termination's on the network cabling. check over here Duly corrected.
To much data sent to the I/O port - clear data with GO or Continue, data may be lost Is the computer on?! Back back to top How did we do? If you are printing from tray 1, verify that the correct paper size is selected in the control panel. 4.
Error 13 Paper Jam Error Message Forms: 13.XX.YZ - additonal location info on display or 13.XX.YY - a jam exists in the media path Paper jams can be in the pickup HP LASER PRINTERS 1200, 2200, 3100 FAX, 3200 FAX, 4100 1. Remove the card and reseat it, try swapping with a know good card from another printer. Replace main motor IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either top or bottom slot.
Better than nothing, of course. Log in / Register Ubuntuhplip package Overview Code Bugs Blueprints Translations Answers Error while printing with HP Laserjet: 40 EIO Transmission Error with hp backend Bug #229981 reported by Ruben Verweij On the II and III Series printers, this error message can be caused by a faulty paper control PCA. http://batteryuniveristy.com/hp-error/hp-error-405-fax.php Back back to top How did we do?
See the catalogue. Back back to top How did we do? You can remedy this by replacing the paper guide plate assembly, RG5-2248-030. Tab missing on top cover.
An HP thread recommends that I update the firmware. ERROR 41-X X= 1,2,4,5 A temporary error occured - Press "CONTINUE" to clear. 41.3 Error - Unexpected paper size - more than one sheet of paper picked up. if this message persists, replace the formatter. Simplify the print job by removing font changes and/or graphics.
I have an HP m603. They could be more informative but they try to balance what they say with what the average reader wants.