Thank you! - unknown 0 From the HP Site. Reconnect the power cord to the rear of the product. Turn the knob on the rear access door counter-clockwise to release the door. Make sure the door snaps firmly into place. (Do not press the buttons on the ends of the duplexer when you reattach it.) Press the button on top of the duplexer his comment is here
If the issue persists, continue with the next solution. When you described "copper contacts" I now realize that must be what I pulled off. (It was copper in color). Ask the community! HP Deskjet 1220C series printers Click Start, click Programs, click HP Deskjet 1220C printer and then click Toolbox.
If the carriage contacts show noticeable damage, contact the HP Customer Care Center listed in the printer's User's Guide. Reach inside the product through the paper output tray, and then manually move the carriage. On the Printer Services tab, click Print a Test Page. Remove any loose paper or obstructions found.
I cleaned all along the connectors (cartridges and printer) reinstalled, cleaned glob of black ink out of corner of printer, unplugged power and connection to computer three times, but to no by unknown on Sep 9, 2008 at 1:03pm Add comment Please sign in to comment 0 See my 4/11/05 8:20 PM post on this thread. Haven't tried the sticky tape trick as it isn't clear how that could help. Hp Deskjet 930c Driver please give me solution quick..............
The self-test report prints. Figure 5: HP Deskjet toolbox Confirm that the Toolbox test page has printed correctly, and that has a color graphic at the top, the words "HP Deskjet" underneath the graphic, and Figure : Open the cover on the product Open the cartridge latch, and then slide the cartridge out of its slot. http://h30434.www3.hp.com/t5/Inkjet-Printing/DeskJet-930C-ink-light-blinks-and-wont-print/td-p/76361 When I wind the service station into place by hand, it seems alright, but the printer never gives up pulsing the cartridges to the left.
Step one: Replace the cartridge Press the Power button () to turn on the product. Hp Printer Lights Flashing Rapidly If the issue persists, continue with the next solution. Step one: Remove loose paper from the tray Remove any loose sheets of paper from the input tray and the output tray. If so, allow the carriage to move to that position.
Release the Power button (). http://h30434.www3.hp.com/t5/Inkjet-Printing/List-of-HP-DeskJet-930c-error-codes/td-p/2584265 Confirm that the sample page has printed correctly, and that it has the correct product name at the top, a graphic in the middle, and an HP logo at the bottom. Hp Deskjet 932c Troubleshooting Blinking Light Click the Services tab, and then click Align to print an alignment page. Hp Deskjet 932c Manual by unknown on Feb 28, 2010 at 10:32am Add comment Please sign in to comment 0 I just bought this printer at our local thrift shop for $10.It has both an
Press the buttons on each side of the duplexer, and then pull the duplexer toward you to remove it. Close the cover on the product. Solution Follow these steps to replace the black cartridge, and then align the cartridges. weblink Figure : Open the cover on the product Open the cartridge latch, and then slide the cartridge out of its slot.
Silly question - Anonymous 0 Reread my post, you did not understand it, I did not say the glob will not occur if you print a lot.If you print a lot Hp Printer Blinking Orange Light Thanks by unknown on Apr 2, 2005 at 7:28am Add comment Please sign in to comment I believe what probably happened was that you allowed the Found New Hardware wizard to The self-test report prints.
Figure : Cartridge error icons Tri-color Cartridge Problem icon Black Cartridge Problem icon Tri-color Cartridge Low-ink icon Black Cartridge Low-ink icon Cartridges OK icon Yellow indicator arrow Once you have determined Method two: Remove the duplexer Press the Power button () to turn off the product. If the HP product does not turn on, press the Power button () to turn it on. Hp Printer All Lights Flashing Step four: Print a self-test report Choose one of the following options to print a self-test report.
Thanks - Anonymous 0 If you squirt water into the service station without disassembling the printer you are just softening the ink.There is a motor on the side of the service Then I turned it off and on again and then it printed like one line in 5 seconds... Check for any paper or objects that might be stopping the carriage. check over here If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting.
Figure : Open the cartridge latch to remove the cartridge Repeat the previous steps to remove the other cartridge. Step two: Print a self-test report Print a self-test report to make sure that the hardware functions correctly. caution: Do not remove jammed paper at this stage. Option one: Print a self-test report from the control panel Press and hold the Power button ().
The yellow arrow points to the Black Cartridge Problem icon The Power light is on and the Cartridge light blinks. Windows Vista Click the Windows icon (), click All Programs, click HP, click the folder for your HP product, and then click the icon for your HP product. Figure : Open the cover on the product Remove jammed paper from the front of the product. Click OK.