Home > Hp Deskjet > Hp Deskjet 3845 Problem

Hp Deskjet 3845 Problem

note: The product might go through a brief warm-up period. A 'Printer cover is open' message displays on the computer The Power light blinks and a 'Printer cover is open' message displays on the computer. Solutions Important: You must follow these solutions in the order presented to resolve the issue. From the drop-down menu on the document or image you are printing, click File, and then click Print. http://batteryuniveristy.com/hp-deskjet/hp-deskjet-3845-help.php

Figure : Click File, and then click Print Click the button that opens the Properties dialog box. If the issue persists, skip to the next solution. Wait at least 15 seconds. Wait until the carriage is idle and silent before proceeding. try here

Disconnect the power cord from the rear of the product. Damaged or dirty paper rollers. When the issue is resolved, you can resume loading paper according to the paper tray capacity specifications for your product. Step one: Remove loose paper from the tray Remove all loose paper from the tray.

  • Then slide the paper width guide inward so that it rests against the edge of the paper.
  • Close the top cover.
  • How to print a self-test report Make sure that plain white paper is loaded in the input tray.
  • Click the Services tab, and then click Service this device.
  • note: You need to use 10 to 20 sheets of paper only for purposes of these troubleshooting steps.
  • If the carriage is on the right side of the product, move the carriage to the left side of the product.
  • If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting.
  • If the product does not turn on by itself, press the Power button () to turn it on.
  • Plug the power cord back into the wall outlet.

Avoid printing on paper that is dusty. How does HP install software and gather data? Make sure to blast the metal chips and dust out of the printer with lots of compressed air!The printer now works fine.Total spent: $4 hardened drill bit, $5 epoxy, Do not leave a cartridge outside the product for more than 30 minutes.

Step one: Perform a power reset Press the Power button () to turn on the product. Figure : Clean the paper pick roller Allow the rollers to dry for 10 to 15 minutes. If the self-test report prints, try printing the original document again. Follow these steps to perform a power reset to try clearing a false paper jam error.

When you have solved the issue, and the product successfully prints a self-test report, there is no need to continue troubleshooting. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, If the issue is resolved, there is no need to continue troubleshooting. The carriage might move to the access area.

Reconnect the power cord to the rear of the product. Source Step two: Clear the paper jam from the rear of the printer Follow these steps to clear any jammed paper from the rear of the product. Figure : Faded, streaked, or missing bars Figure : Broken pattern lines or a missing color pattern If there are no issues on the self-test report, the issue is resolved. If these steps resolved the issue, and the self-test report prints, there is no need to continue troubleshooting.

Figure : Rotate the paper rollers Lightly dampen the swab with the water, and then squeeze any excess liquid from the swab. http://batteryuniveristy.com/hp-deskjet/hp-deskjet-problem.php See the documentation that came with the HP product for more information. Click Align the Device, click Align, and then follow the on-screen instructions. The only solution I've found is to reboot the PC.

Press the Power button () to turn on the product. Store paper in a cool, dry place. Gather the following materials: A clean, lint-free cloth, or any cloth that will not come apart or leave fibers A clean, lint-free swab that will not come apart or leave fibers http://batteryuniveristy.com/hp-deskjet/hp-deskjet-3845-problems.php Figure : Clean the contacts Copper-colored contacts Ink nozzles (Do not clean) Place the cartridge on the sheet of paper or paper towel, and allow the cartridge to dry for 5

note: Use a flashlight to thoroughly check the inside of the product. When an indicator shows low ink levels, consider having a replacement cartridge available to avoid possible printing delays. Figure : Lift the output tray Slide the paper width guide to its outermost position.

Here's their way of solving it:>http://h10025.www1.hp.com/ewfrf/wc/document?dlc=en&lc=en&product=372330&lang=en&cc=us&docname=npd09305 Flag Permalink This was helpful (0) Back to Peripherals forum 10 total posts Popular Forums icon Computer Help 51,912 discussions icon Computer Newbies 10,498 discussions

The Printer Properties window opens. The paper might not have been loaded far enough into the product. Sorry, there was a problem flagging this post. If the issue persists, continue with the next solution.

See your browser's documentation for specific instructions. {} Z7_3054ICK0KGTE30AQO5O3KA30U5 hp-support-head-portlet Actions ${title} Loading... Complementary Content Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Then slide the paper width guide inward so that it rests against the edge of the paper. http://batteryuniveristy.com/hp-deskjet/hp-deskjet-3845-missing-file.php Repair fees might apply for out-of-warranty products.

Ask the community! I hated to discard my faithful 3845, so I took the top cover off. HP Customer Support Z7_3054ICK0KGTE30AQO5O3KA30U7 hp-contact-secondary-navigation-portlet Actions ${title} Loading... Figure : The Power light blinks Cause The product requires maintenance, or is in an error state How do I resolve this issue?

Step four: Print a self-test report Print a self-test report to make sure that the hardware functions correctly. Step four: Make sure that the carriage moves freely Follow these steps to make sure that the carriage moves freely. Step one: Remove loose paper from the tray Remove any loose sheets of paper from the input tray and the output tray. Modify your browser's settings to allow Javascript to execute.

Figure : Replace the rear access door Reconnect the power cord to the back of the product. HP Customer Support Support Home Products Software and Drivers Forums Contact Support Search Select your Model Let HP find my products Identify now HP can identify most HP products and recommend Z7_3054ICK0KGTE30AQO5O3KA30N0 hp-concentra-wrapper-portlet Actions ${title} Loading... Open the top cover.

I am an HP employee.*Say thanks by clicking the "Kudos! Lower the output tray, and then close the top cover. If the test page does not print, continue with the next solution. If the cartridges are compatible with your product, try the following solutions in the order presented.

If the self-test report prints successfully, there is no need to continue troubleshooting. The problem was obvious -- When it tried to print a test page, the grey plastic gear on the end of the feed roller just spun. Apply a moderate amount of pressure to make sure that you remove dust or dirt buildup. To resolve the issue, try each solution in this document, and then use the steps in this section to print a self-test report.

Cause Any of the following issues can cause this issue: The paper trays are empty or overloaded. If the HP product does not turn on, press the Power button (). A 'No Print Cartridges Have Been Detected' message displays on the computer The Power light blinks and a 'No Print Cartridges Have Been Detected' message displays on the computer.

© Copyright 2017 batteryuniveristy.com. All rights reserved.