Turn on the printer. Other causes include poor quality parallel cables, poor connections, or general communication problems. If this message persists, contact an HP-authorized service or support provider. Reduce the complexity of the print job to avoid this error. http://batteryuniveristy.com/hp-color/hp-color-laserjet-3600n-error-codes.php
alternates with LOAD TRAY XX: [TYPE] [SIZE] Description Paper is loaded that is longer or shorter in the feed direction than the size configured for the tray. Press (Select) to select CALIBRATE NOW or QUICK CALIBRATE NOW . Call hp and they will replace with a 620N at no charge. Any luck with this problem?Tim - Anonymous I have tried replacing both, the high voltage power supply and the DC controller pca to no avail. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=74301
Press (Select). If this message persists, contact an HP-authorized service or support provider. Careful ! alternates with TO CONTINUE TURN OFF THEN ON Possible printer control panel error message 59.0K 59.3K 59.6K 59.8Y 59.BC 59.0C 59.3C 59.6C 59.90 59.BM 59.0M 59.3M 59.6M 59.9K 59.BY 59.0Y 59.3Y
Wait for the printer prompt to install each print cartridge. The test page can use only tray 2 as the paper source, so make sure that paper is loaded in tray by Stephen on Feb 12, 2007 at 5:34pm Add comment Open the ETB. Hp 4600 Paper Pickup Assembly When the memory starts counting, press and hold the green (Select) button.
top 10.00.YY SUPPLIES ERROR For help press ? 51.2c Printer Error Action Open the covers and the Electrostatic Transport Belt (ETB). I've been working with these printers for about 5 years and they are all still in service. Turn on the printer.
Reseat or replace memory in DIMM Slot J3. http://printcopy.info/?l=en&mod=erc&brand=HP&model=Color%20LaserJet%204600 If the message returns, check the memory DIMM in Slot J4 to ensure it is supported memory. Hp 4600 Laser Scanner Assembly by Stephen on Dec 5, 2007 at 2:04pm Add comment Please sign in to comment 0 Season's Greetings,Ok, my 4600 is printing all of my documents that have graphics out of 68.0 Permanent Storage Write Fail Hp Printer Thank you.
top 54.1 PRINTER ERROR Description A low fuser temperature error has occurred. http://batteryuniveristy.com/hp-color/hp-color-laserjet-2600n-error-50-2.php Watch the control panel. NOTE: These orange shipping blocks are located just behind two blue plastic thumbscrews used to hold the fuser in place. It is only on the large dark prints when this problem occurs. Hp Color Laserjet 4600 Service Manual
by dekuda on Jan 5, 2005 at 2:12pm Add comment Please sign in to comment What coes the engine test look like? Release the check button when the Ready, Data, and Attention light are on steady. Press (Down Arrow) to highlight CALIBRATE NOW or QUICK CALIBRATE NOW . http://batteryuniveristy.com/hp-color/hp-color-hp-laserjet-2840-error-codes.php Description One of the covers is not completely closed.
Pull paper by both corners to remove it. Hp 4650 Cold Reset Watch the control panel. The 80 error indicates that the Color LaserJet 4600 series printer is experiencing a problem with either the printer's network card or the network connection to the printer.
Press (Down Arrow) to highlight PRINT QUALITY . Perform a cold reset. I shot you an email explaining. 68.2 Permanent Storage Write Fail Action Turn the printer off, and turn it on again.
top 53.11.YY PRINTER ERROR TO CONTINUE PRESS CANCEL JOB Possible printer control panel error message 53.11.00 53.11.01 53.11.02 53.11.03 53.11.04 53.11.05 Description An error occurred with the printer’s memory in DIMM If not I can help you do this.Third, there are four colored 90 degree anges in each corner of the cofiguration page. It may be time to change it. this content Continue holding the green (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady.
I have had this problem in the past with cartriges that are re-manufactured.....and had to change vendors due to the fact that they changed the type of color they put in...You by Stephen on Mar 26, 2009 at 11:46am Add comment Please sign in to comment 0 We have one of these in a student computer lab (both Mac and PC); all It used to work find so my assumption is the NIC card has gone wacko. Now I hope I can get my supplier to replace the defective cartridge!
Continue holding the green (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady.