Home > Hp Color > Hp Color Laserjet 3600n Error Message 54.17

Hp Color Laserjet 3600n Error Message 54.17

Perhaps some rollers need a little cleaning. Replace any defective sensors or flags. 13.10 PAPER JAM CHECK DUPLEXER Jam at duplexer. 1. If the message persists with different software applications and print jobs, disconnect all cables to the printer that connect it to the network or printer. 5. After all, it is not as difficult as I though it would be. his comment is here

Remove all media in the paper path, and then open and close the top cover. 2. Check sensors and flags in the paper path for proper operation 13.1 PAPER JAM OPEN INPUT TRAYS Paper-delay jam at paper feed area. 1. We returned it. Be careful not to let the spring loaded shutters fall out. http://h30434.www3.hp.com/t5/Inkjet-Printing/Color-Laser-Jet-3600-error-54-17/td-p/5068825

I did the same what you mentioned to solve this issue. Bonny Reply Mike on September 20, 2011 at 8:28 pm Hi Bonny. Keep in mind you have to align the white gears that the MDA fits into when installed.

  1. Ted Reply Mike on November 4, 2011 at 5:05 pm Hi Fr.
  2. Replace the print cartridge interface for the cyan/black cartridge.
  3. or does it get to the printer and then the printer says no?
  4. Replace the engine controller board. 4.
  5. This is not for the faint of heart, but it isn't too terrible.
  6. Reply Teddy on November 2, 2011 at 8:31 pm Mike, dear !
  7. If you skip the calibration, the printer comes to the ready state and correctly displays the toner filling levels.

It may be telling me it's just too tired…. ?? Check and reseat the fuser and toner cartridge to make sure they are not hindering gear movement in the drive train. 3. I've looked into getting a multipurpose high volume printer and copier for my office but I just don't have enough volume to justify the lease. We know that you don't want to spend hours trying to figure out a printer problem.

Remove the cartridge, check physically toner is available or not.(It may show in display)2. Hermann Reply Dennis on July 26, 2016 at 1:20 am Mike, you saved me once before about two years ago, but then I forgot about this. Tip: The max point reward for answering a question is 15. Follow the instructions to remove the "Laser/scanner assembly".

After cleaning you can enjoy the printer without endless calibration. or when I press the Menu button. Or just drag it here! Only after I performed the "Skip Calibration" process would the printer stop calibrating.

You can get a ready-made kit for DIY repairs, or you can select parts individually. http://www.mikekrauss.com/hp-3600n-constantly-calibrating-fix/ It may be useful to others who encounter the same thing. I read only some HP service manual for that printer but the procedure on how to exchange the lever was not described there. Service manuals, Parts Catalogs, Error Codes, Troubleshooting, Service Menu, Adjustment, Reset Codes, Compatible Devices, Equivalents Parts and Circuits diagrams.

Corporal: An expert that has over 10 points. this content Ensure the media does not exceed the maximum length. 4. Remember, as soon as you cycle the power off and then on, you have to press and hold the down arrow. It first started with a broken cartridge lock lever.

However, my color printouts all have an ugly yellowish tinge, even after running the quick calibration. Turn the printer off/on to attempt to clear or reset the message. Verify the paper tray is fully closed. 3. weblink If you're having no luck and need to know how to bypass the empty cartridge warning, let me know and I'll go figure out the step-by-step procedure.

Let me know how this works out. Both the Yellow and Magenta optics have a mirror which faces up so dust gets in and collects on those mirrors. The printer may not allow you to do this since we would assume the old toner cartridge is empty.

I've found that HP brand toner cartridges work the best.

By the way, I did make a small donation via Paypal. Reply RF on September 10, 2013 at 6:06 pm You are the man! The page containing the error will automatically be reprinted. 2. Reply Paul on February 17, 2011 at 1:28 am Your method got me printing again, but, it is printing ONLY Cyan and black.

Thanks for taking the time to post these very clear directions. If the message will not clear: 1. I think I'm going to call it a night… I'll check tomorrow to see if you had a chance to reply… and if it works tomorrow, I'll let you know. check over here Call for Assistance 877-755-5300 Home About Us Contact Us Search Site Map Printers Supplies Accessories Parts Error Codes Login Shopping Cart Return Policy Privacy Policy Orion Printers and Parts 6030 Marshalee

If it works, it's a bummer that you had to buy a new cartridge, but at least you won't have to go through the hassle of getting a refund. Reply Bonny on September 8, 2011 at 4:08 pm Thanks Mr Mike! for the error message follow what it says so if the error is no connection check that the wires are attached. But my replacement is a HP Original.

Reseat the EIO card in slot [X]. 41.1 41.3 41.4 41.5 A temporary error occurred while printing. I should note that I was not having the same color errors as this guy. Reseat the external paper handling device. 4. If the job prints, go back to the first application and try printing a different file. (If the message only appears with a certain software application or print job, contact the

With many thanks! - penny Reply Mike on November 8, 2011 at 7:52 pm Hi Penny, I would try performing a "Full Calibration." This is performed exactly the same as a Also, replace separation pad. 5. I will difinitely keep up with this thread, in case this happens again. Thank again.

I am eternally grateful Reply Jane on September 21, 2012 at 2:14 pm Hi Mike… as it turns out - the quality is atrocious… and not really useable. Once they are talking, it's usually up to the printer to make nice and give quality output 🙂 Let us know how it works out. fr. Add × Loading...

Reply David on October 1, 2015 at 7:02 pm Hi Mike, I was excited to try the "fix" that you recommended for the calibration problem but have had no success after Or just drag it here!

© Copyright 2017 batteryuniveristy.com. All rights reserved.