It may be useful to others who encounter the same thing. It seems as though it changes after any type of calibration is done. Thanks a lot. I replaced the ink cartridge but it still giving the same error message. his comment is here
DO NOT yank. Thanks. Just a thought, but I would try removing a cartridge at a time and then try the entire procedure again. Maybe there's something wrong with one or more of them-they were remanufactured ‘hp compatible' cartridges. http://h30434.www3.hp.com/t5/Inkjet-Printing/Color-Laser-Jet-3600-error-54-17/td-p/5068825
Thank you for your practical, easy to follow steps & visuals. Thanks again….. user-manual-Deskjet 6940... Reply Mike on February 17, 2011 at 2:36 am Hey Paul, Did you start getting the "stuck in calibration" after replacing one or more of the cartridges.
Reply RD on February 3, 2011 at 4:24 pm Thanks for that - worked a treat. Keep in mind you have to align the white gears that the MDA fits into when installed. I have completed the additional steps said to address this problem; and after reading all of the comments above, also went back through everything, and selected "Full Calibration" -- but all My honest opinion, it was replacing all the toner cartridges and performing the two procedures above that returned my printer to full "normal" high quality printing operations.
Not even to change the power supply or installing the ram or hard disk myself. Thanks for the advice guys but eventually fixed it by replacing the gear assembly. You can print your Parts List or export to Excel to further work with him. http://www.fixya.com/support/t15354123-hp_3600_54_17_error Reply 0 Re: Color Laser Jet 3600 error 54.17 08-21-2013 09:18 AM Our printer is functional again!
It accelerates downloading without errors. Now when I print anything the page is completely yellow! So there are two choices: Replace the misbehaving toner cartridge (and rerun the procedure) or deal with the misbehaving toner cartridge. I would think you need to replace the MDA unit, align it as it should be and all will be good.
Press the "Down" Arrow button 1 time until you see "Print Quality." Press the "Check Mark" Button once. http://printcopy.info/?l=en&mod=erc&brand=HP&model=Color%20LaserJet%20CP5225&code=54.17 However, we all know this is an expensive test to run. I paid ASK and their instructions were all off and led me to open new cartridges that were not necessary. Well the black was first to go and when we replaced it the printer restarted and wouldn't exit startup calibration.
You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. http://batteryuniveristy.com/hp-color/hp-color-laserjet-3600-error-59-c0.php My suspicion is that the reason why the printer starts malfunctioning like this in the first place is because one of the printer cartridges does require calibration - even if it Press the "Down" Arrow button 2 times until you see "Configure Device." Press the "Check Mark" Button once. We have tried full calibrations multiple times, new cartridges, etc.
Remove the Electronic Transport Belt and raise the arms that it sits in, to fool the printer that it is installed and closed. I'm not sure why? Please enter a valid email address. weblink Once the clean up is done and the printer is printing, go to Information/Diagnostics and Print the Event Log.
So I too would have been a bit peeved if I then had to buy a new printer. Grab firmly near the connectors, try to make sure you are pulling all the wires evenly. Judith Rickard Reply Chris on December 17, 2015 at 1:59 pm thanks, mike : ) I just read your instructions to a friend.
Make sure that connector J1020 onthe DC controller is seated correctly.2. These directions were the most precise and easy to ofllow I have come across since using the computer. I am eternally grateful Reply Jane on September 21, 2012 at 2:14 pm Hi Mike… as it turns out - the quality is atrocious… and not really useable. I replaced the yellow cartridge AND put one of the Cyan cartridges back in and it finished the calibration completely.
That's the second part of the process. I can now print! Push and wiggle a very little, the cable will slide in a little bit each wiggle. check over here I was an electronics technician in the Navy for 6 years and I realized after taking my printer apart that it was a huge mistake!
If it works, it's a bummer that you had to buy a new cartridge, but at least you won't have to go through the hassle of getting a refund. Mike Reply Raja on March 8, 2011 at 12:18 pm Hi MIke. Each time I bought a 2nd new cartidge to test and still had problems. Beside using a hammer and TNT do you have any other suggestions?
I never format a computer by myself. After cleaning you can enjoy the printer without endless calibration. I went through your steps on initializing and the Red, "Attention" light went on.