Home > Hp Color > Hp Color Laserjet 3600 Error 59.30

Hp Color Laserjet 3600 Error 59.30

You should be able to Google a free download for the service manual, it is 362 pages. Check that connectors J5002 on the ETB motor and J206 on the driver PCA are seated correctly. Powered by Blogger. Check that connectors J5008 on the fuser motor and on the driver PCA are seated correctly. 2.Turn printer on and check and see if fuser motor start spinning. his comment is here

Open the tray and the front door and clear the jam. Turn off the printer. The email address entered is already associated to an account.Login to post Please use English characters only. Plug the printer into a different power outlet. http://fix-your-printer.blogspot.com/2012/10/solving-error-5930-on-hp-color-laserjet.html

If the message persists, replace the output-bin-full sensor. If the message persists, turn the printer off then on. Event-log messages Event code Description 54.06 Color-density-sensor error 54.14 Color-plane-registration sensor error 54.1200 Black-density measurement abnormality 54.1201 Cyan-density measurement abnormality 54.1202 Magenta-density measurement abnormality 54.1203 Yellow-density measurement abnormality 54.1500 Black density

  1. This message appears when the printer is turned on and begins initialization.
  2. Have a manual for Printers & Copiers?
  3. Close the front door.

HP - Updating Drivers As soon as you purchase a new HP Cp1215 Color LaserJet Printer, those hardware drivers that were included with it are already in need of an update! Remove the fuser. Was the information on this page helpful? I'm hoping a replacement fuser unit (Q7503A - 220v) will be the fix, but I don't want to waste £250 and find it isn't the cause Many thanks in advance Reply

Invalid driver Press OK The driver is not correct for this printer. Close the front door. Does anyone know the definitive cause of this error code on this printer? The printer is ready and will print for the estimated number of pages indicated.

Replace the DC controller PCA. Check that connector J1020 on the DC controller PCA is seated correctly. If there is no conduction in the fuser heater, measure the resistance between fuser connectors J6007LAF-1 and J6007-2. Add Comment Nickname: Your Email: Subject: Comment: Enter the code below: Knowledge Base Software by: KnowledgeBase Manager Pro v6.2.2 Community Development JavaScript must be enabled in order for you

Sensor Error Turn off then on A problem has occurred with the top-of-page sensor. http://printcopy.info/?l=en&mod=erc&brand=HP&model=Color%20LaserJet%203600&code=59.30 Parts are thoroughly tested, inspected for damage & defects and guaranteed 100% fully functional. $229.00 Call for Assistance 877-755-5300 Home About Us Contact Us Search Site Map Printers Supplies Accessories Parts HP CLJ 4700/4730/CP4005 Fuser Roller Drive Assembly RM1-1729-ROConclusion About The 59.30 Fuser Error on Your HP Color Laserjet 4700, 4730, CP4005Not a bad job. Related Articles 4000/4050 Maintenance Kit 59 .X Printer error Troubleshooting and Correcting Power Problems 57.XX Repetitive image defect chart HP LJ 2400 Remove the ECU board HP LJ P3015 Fuser removal

If you believe you purchased an HP supply, go to www.hp.com/go/anticounterfeit . this content Replace the driver PCA. 59.51 Error 59.61 Error An error occurred with the cyan print-cartridge drive motor during startup or rotation. Replace supplies At least two print cartridges are out and need to be replaced. Replace DIMMs and EIO devices as necessary.

or its affiliates. To use Knowledgebase Manager Pro, enable JavaScript by changing your browser options, then try again. If the resistance is not 5 ohms to 1 kohms (100 to 127 V) or 20 ohms to 1 kohms (220 to 240 V), replace the fuser. weblink Replace the ETB motor.

Replace the DC controller PCA. 50.2 Error: Verify the fuser is installed correctly and fully seated. If not the cart. Have you tried re-seating the the transfer unit?

Remove the fuser.

Replace the print cartridges. Disconnect all cables except the power cord. Help Desk » Inventory » Monitor » Community » PrintCopy .infoservice Service manual Parts List Error Code Equivalency Sign In Contacts About Us Service manual Error Code Parts List Equivalency Use this test to rotate the fuser motor and drive gears.● Fuser  pressure release motor.

Check that connector J6007 on the fuser is seated correctly. Replace the connector as necessary. Turn the printer off and then on. http://batteryuniveristy.com/hp-color/hp-color-laserjet-3600-error-50-9.php I tried a new fuser.

If the fuser  seemed fine and the main gear seemed to turn with little resistance  then I would replace the fuser  motor. XX Description: 15 Yellow 16 Magenta 17 Cyan 18 Black Make sure that connector J1020 on the DC controller is seated correctly. Load the trays with the type and size for which they are configured. Solution 3: Replace the fuser Solution 4: Replace the fuser drive motor Solution 5: Take the left side cover off.

Measure the resistance between fuser connectors J6007LA-1 and J6007LA-3. However, it seems JavaScript is either disabled or not supported by your browser. If the problem persists, replace the fuser. Non-HP installed alternates with To accept press OK A new, non-HP supply has been installed.

Replace the driver PCA. 59.C0 Error An error occurred with the developing separation-drive assembly. New service manuals Canon imageCLASS MF416dw, (sm, pc), Eng, 30.6Mb Samsung SLM3825ND, (sm, pc), Eng, 26.8Mb Kyocera-Mita ECOSYS M6535cidn, (sm, pc), Eng, 137Mb Samsung Xpress M2876ND, (sm, pc), Eng, 12.7Mb Samsung Turn the printer off and then on.

© Copyright 2017 batteryuniveristy.com. All rights reserved.