Home > Hp Color > Hp Color Laserjet 3500 Error 47.01

Hp Color Laserjet 3500 Error 47.01

Microsoft® is a U.S. Corporate Product Regulations Manager, 3000 Hanover Street, Palo Alto, CA 94304, USA... San Rafael, CA Great that you have that part in stock and thank you for your quick reply. Page 101: Using An Ascii Pjl Escape Sequence To Set Security Use HP Web Jetadmin software, HP LaserJet Utility for Macintosh, or an ASCII escape sequence to set security. http://batteryuniveristy.com/hp-color/hp-color-laserjet-3500-error-59-a0.php

Engine control system 2. Loosen and remove the two retaining screws holding the EIO slot cover to the printer and remove the cover. Page 126 6. Lift and pull the lower rear door (rear output bin) while using your finger to press the tab with ridges on the left side of the door. you can try this out

Normaalissa käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen ulkopuolelle. Page 113 3. Page 90: Usb Configuration, Connecting The Usb Cable USB configuration All printer models support USB connections. Page 46: Identification, Model And Serial Numbers, Power And Regulatory Information, Table 1-12.

See Image formation system for the details on image formation. Page 158 Primary transfer bias generation The primary transfer biases (TR11, TR12, TR13, TR14) are output to transfer the toner on the photosensitive drum to the ITB. Laser/scanner unit ..................139 Figure 5-21. Switch locations ....................250 Figure 6-67.

This warranty does not apply to print cartridges that (a) have been refilled, refurbished, remanufactured or tampered with in any way, (b) experience problems resulting from misuse, improper storage, or operation So I followed your advice and replaced the foam on SL4, that fixed the problem :) It was quite a bit of work, buried so deep in the printer. Recycled paper must meet the same specifications as standard paper. other Page 60: Chapter 1 Printer Description 24 March 2004 For Regulatory Topics Only: European Contact Your Local Hewlett-Packard Sales and Service Office or Hewlett-Packard Gmbh, Department HQ-TRE / Standards Europe, Herrenberger

Static electricity can damage DIMMs. Over time, this buildup can cause print-quality problems, such as toner specks or smearing. If the message NEW FUSER KIT appears, go to step 11. Printer Security Levels Setting security on the printer This printer features control panel locking, which allows network administrators to prevent users from changing certain printer control panel settings.

After replacing the fuser, you must also replace the pickup roller. http://printcopy.info/?l=en&mod=erc&brand=HP&model=Color%20LaserJet%203500&page=3 Check with your local HP dealer to determine the services available to you. This requires removal of the cover and then the fuser as the shaft with three rollers is located on the fuser assembly. Replace Tray 2. 9.

Page 110 3. check over here back to top How did we do? •HP LJ 4600 Laserjet 4600 exhibits rough and or unfused print on left or right edge for 1" to 1.5" into page. The HP Color LaserJet 3500 printer is a four-color laser printer that prints 12 pages per minute (ppm) in both monochrome (black and white) and color. Function of solenoids Name Function SL2 Tray 2 (cassette) pick-up solenoid Drives the Tray 2 (cassette) pick-up roller.

  • The DC controller judges the fan faulty and sends the error message to the formatter when the /FANS signal has not been input (turns “H”) for 10 seconds or more.
  • You can set the length of time before the printer goes into PowerSave mode to 1 MINUTE, 15 MINUTES, 30 MINUTES, or to 1 HOUR, 1.5 HOURS, 2 HOURS, or 4
  • Also in step 13 (reinstallation tip), you should also insert the axle for gear 1 into the printer, because it needs to grab a keyed hole inside the printer.9.
  • Interface troubleshootingpage 427................................................................................................................................................................

Pull the drawer out until it reaches the stops. Part# RC1-1247-000 - Lever, ITB Coupling, It's the same part for HP Color LaserJet 3500 and 3700. On the Configure tab, click More. 4. his comment is here The two release levers are located on the left and right side of the lower rear door. 7.

If this is special paper, such as letterhead, load it with the side to be printed down and the top edge toward the front of the tray. by laserphil on Nov 11, 2009 at 12:22am Add comment Please sign in to comment thanks for the quick response. My assembly was missing one of the O-rings which was attempting to send belt out of range.

Function Of Solenoids, Table 5-4.

You can view the HP Toolbox when the printer is directly connected to your computer or when it is connected to a network. Page 65: Search Approach 4 Service approach Chapter contents This chapter contains the following sections. The phone numbers for ordering supplies are: ● U.S. In step 27 and 28, you need to look at both pictures (figure 6-24 and figure with no number) to find all the right screws.

Page 136 Chapter 4 Printer maintenance ENWW... In step 13 (reinstallation tip), the gears are shown in figure 6-35 "above", not below.8. In the "Secondary transfer roller engaging solenoid (SL4) removal" procedure (page 265), both pictures show SL1 on the left and SL4 on the right. http://batteryuniveristy.com/hp-color/hp-color-laserjet-3500-error-41-7.php Sensor locations ....................252 Figure 6-69.

Hewlett-Packard recommends using HP Color LaserJet Soft Gloss paper with this printer. Generated Thu, 24 Nov 2016 14:10:06 GMT by s_wx1196 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection Open Tray 1, and raise the output bin extension. Place your thumbs on the blue ridges (near warning label) and, using fingers, pull up on the blue latches.

Page 49 ● Do not use paper that is embossed or coated, and that is not designed for the temperatures of the HP Color LaserJet 3500/3550 and 3700 series printer image This may be due to abnormal characteristics of the printing environment or to other variables over which Hewlett-Packard has no control (for example, extremes in temperature and humidity). Chapter contents ........................4 1 Search approach ........................4 2 Parts and supplies ........................43 Ordering parts ........................43 Ordering supplies ......................43 Exchange program ......................44 Supplies ..........................4 4 World Wide Web .......................44 HP service parts Remove the orange tape and orange shipping locks on the rear, left, and right sides of the transfer unit.

Page 100: Setting Security On The Printer, Locking The Control Panel, Table 3-4. Reset Memory: Resets the printer to user-specified default settings. The engine control system consists of the following: ●... Faulty secondary transfer engagement sensor.

Chapter 1 Printer description ENWW...

© Copyright 2017 batteryuniveristy.com. All rights reserved.