Home > Error Hp > Hp Error 57

Hp Error 57

Contents

HP LASER PRINTERS 5000, 5100, 52001. For example, 1 = fan motor 1. When prompted, save the installation application in the Temp file folder on the C: drive. Recommended action Select the correct print driver. his comment is here

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 20 minutes and turn the printer on (condensation may be causing error and the Home | contact Us | About Us | Terms of Sale | FAQ | HP Maintenance Kits | HP Fuser Assemblies | HP Color Supplies |HP Parts Lexmark Maintenance Kits | Could also be a failure of the power supply. 4L/4P/5L/5P/6L/6P most likely cause is a bad ceramic heating element. Recommended action Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). http://www.printertechs.com/printer-troubleshooting/hp-error-codes

52 Scanner Error Hp Laserjet

All fans are enabled to low speed operation at power on. Attempt to print. Check these items. Plug the printer into a wall outlet and see if this resolves the problem. 2 If the printer is already plugged into a wall outlet, try another power source in the

Fan operation is verified during device power up. Plug the network cable in and print a test page from the workstation. Extremely heavy or thick paper is also a problem. 59.f0 Error Hp Printer Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

Change the main motor.4. Manual feed , Press [OK] for available media Description The product is set for manual feed mode. Replace the formatter and/or firmware DIMM. 4. http://www.printertechs.com/printer-troubleshooting/408-57-1-57-3-57-4-57-5-57-6-57-7-57-8-hp-laserjet-9000-9040-9050 If the error re-appears, call HP for technical support to troubleshoot the problem.

If it does not, try reprinting the job. 52 Scanner Error M521dn How about the I/O port - damaged, seated properly, pins not bent? 4+/5P/5 The computer and printer aren't talking because of improper signal protocols. If no error appears, try to print a file (problem is resolved if printer prints the file with no error). Secure the DIMM access cover back onto the printer.

  1. CAUTION: Do not turn power off or unplug the printer until prompted on the front panel display.
  2. If the error continues, call HP for technical support to troubleshoot the problem.
  3. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.
  4. Recommended action Press ENTER on the printer's front panel to continue.
  5. Click here for information on contacting HP Customer Care.
  6. Reseat J205,206,207 and laser scanner connectors.
  7. Recommended action Turn the printer off, using the main power switch located on the back of the printer.

50.0 Fuser Error

Replace the fan. http://www.fixyourownprinter.com/posts/9213 Caution needs to be used when installing the new assembly - be careful of the sensor flag spring! 5Si - Can be caused by field replaceable units (FRU's) not installed correctly. 52 Scanner Error Hp Laserjet On the printer's front panel, scroll to the Cartridges menu. 50.0 Fuser Error Hp Laserjet P1102 Check display panel for media request.

top System Error 010042 Explanation An error has occurred in the Service Station-axis Encoder quadrature. this content Actual cartridge life may vary. If the error re-appears, turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. top System Error 0C1000 (non-continuable) Explanation The primer is not calibrated or the calibration settings have been lost. 50.0 Fuser Error Hp Laserjet P1108

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. HP LASER PRINTERS 2P, 2P+, 3P 1. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. weblink If no error appears, try to print a file (problem is resolved if printer prints the file with no error).

If problems persist, continue with the remaining steps. 50.0 Fuser Error Hp Laserjet P1007 Recommended action Press ENTER on the printer's front panel to continue (the printer will still function, although the Drop Detector is not calibrated). If the error continues, call HP for technical support to troubleshoot the problem.

On some printers you can press the select button to try to continue.

Turn the image adapt and page protect to ON or AUTO either from the control panel or from within HP Explorers Remote Control Panel. 5P/5Si Same as above, Press GO to Pretty rare though. Recommended action Close the door. Hp Printer Error Code List Pdf top System Error 0A0010 (non-continuable) Explanation A problem with the Air Pressurization System (APS) has occurred.

Open the cover on the back of the printer to access the ink cartridge assembly (right side of the printer, looking from the back). Press GO. top System Error 0B000B (non-continuable) Explanation Air Pressurization System failure. http://batteryuniveristy.com/error-hp/hp-error-59.php These can be set within the Remote Control Panel.

Turn the printer on. HP 4/4+/5 most likely cause is burned out quartz lamp. We sell maintenance kits, fuser, repair parts and supplies.

Error Codes Error 10 - Supplies Memory Error 10.XX.YY Exact format is dependent on printer model The printer is unable to Figure 5: 5000 series Mark encoder Remove the lens cover from the printhead carriage by pulling it straight out of the slot on the right side of the printhead carriage.

YOU CAN EVEN SWAP IT OUT FOR ANOTHER "TONER ASSY" [FOR TESTING PURPOSES], IF YOU ALREADY HAVE AN EXTRA REPLACEMENT ON HAND. If the error re-appears, call HP for technical support to troubleshoot the problem. If the error continues, call HP for technical support to troubleshoot the problem. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

Order the HP II/III Service 50 Error Repair Kit Quartz fuser lamp is burned out. This document contains a comprehensive list of various support services available to help solve printer problems. Recommended action Turn the printer off, wait 15 seconds and turn the printer back on (the error should disappear). Main motor not functioning properly. 2 Change the toner cartridge. 3.

Turn the printer off, and then turn the printer on. 2. Recommended action Turn the printer off (using the power switch at the back of the printer), and check for obstructions in the Carriage path (Scan-axis) and remove if found. Check the fan’s connector and make sure the fan is not blocked. 2. controller board.

If the error continues, call HP for technical support to troubleshoot the problem. If the error continues, call HP for technical support to troubleshoot the problem. Plug the product directly into the wall socket. Replace the controller board.

© Copyright 2017 batteryuniveristy.com. All rights reserved.