Home > Error Hp > Hp 4 Code 57

Hp 4 Code 57

Contents

To start viewing messages, select the forum that you want to visit from the selection below. The toner cartridge is OK because it has been inserted during a successful motor self test. Terminate the port on the printer with a BNC T and two 50 ohm termination's. The motor ran the normal five seconds and the display read WARMING UP. his comment is here

I measured the resistance across the large terminals for the fuser and got 2.2ohms on the new, and 2.5 ohms on the old fuser. controller board. HP Cartridge 56 (Black) & 57 (Colour) Cartridges for HP PSC 1210. 11. controller.HP LASER PRINTER 8100, 8150 ERROR 57.21. http://printertechsforum.com/forum/showthread.php?2799-LaserJet-4-57-Service-amp-57-Fuser-Messages

57.03 Error Hp 9050

Replace the D.C. Depending on the model, a firmware DIMM may need replacing or a flash update. On some printers you can press the select button to try to continue. Remove and reseat the optional interface card.

  • Replace main motor IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either top or bottom slot.
  • Fan error.One of the cooling fans is bad. 2.
  • Replace the fan.HP LASER PRINTER 2015 ERROR 571.
  • Fan error.One of the cooling fans is bad. 2.
  • Replace the D.C.
  • Fan on main body. 3.

Back back to top How did we do? Fan operation occurs only during power up or during a print job.2. Service manual says this should be “about two ohms.” I next measured the resistance across the upper pair of small terminals for the fuser and got 248 K ohms on the Rh7-5297-000cn I tried the standalone download from your linkhttp://www.microsoft.com/download/en/details.aspx?displaylang=en&id=22but I get the message 'setup.exe has stopped working (close program)'.

Plug the printer into a wall outlet and see if this resolves the problem. 2 If the printer is already plugged into a wall outlet, try another power source in the Reset as needed. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎12-15-2013 09:01 AM Hello Paul I am also trying to installMicrosoft .Net http://www.advancedlaser-hp-error-codes.com/error_57.htm Replace the drum drawer ass'y.HP COLOR LASER PRINTER 4600, 5500 ERROR 57.31.

Thank you for the speedy shipment and response. Rh7-5296-000cn X represents the error location and can equal one of the following: 1 = Slot number 1 2 = Slot number 2 3 = Slot number 3 6 = Card in How about the I/O port - damaged, seated properly, pins not bent? 4+/5P/5 The computer and printer aren't talking because of improper signal protocols. Listening for the exhaust fan.

57.07 Error Hp 9050

The +5 VDC enables the +24A VDC.) "2. why not try these out Is the computer powered off! 57.03 Error Hp 9050 Gears seized. 2. Rh7-5294-000cn If you can turn the motor 15-20 times without encountering much resistance and it turns smoothly, I would guess that you don;t have a bind in the gears.

Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎04-23-2012 01:15 PM Had to F11 my Vista 32bit Desktop (Presario SR5210NX) http://batteryuniveristy.com/error-hp/hp-error-code-49-4c06.php Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎12-15-2013 09:22 AM Hi:Try first manually installing Vista SP1 then SP2 from Check the fan cable connectors.3. Can also be formatter PCA. Hp Laserjet 9050 Error Codes

I am looking in particular for the error code 57 > on an HP laser jet 4. AS YOU REPLACED THE "MAIN MOTOR" ALREADY AND IT DID NOT CORRECT YOUR PROBLEM, WE WILL ASSUME THE NEW MOTOR WAS "GOOD" AND "CORRECTLY INSTALLED"...Its also possible that the GEAR TRAIN Reply 0 0 Paul_Tikkanen Provost Posts: 78,269 Member Since: ‎07-13-2010 Message 8 of 12 (6,756 Views) Report Inappropriate Content Re: Error code 57 Windows Update (Kb951847)x86 NET Framework 3.5 SP1. weblink Poorly seated motor cables or connectors. 4.

Defective toner cartridge in the Laserjet 4 Plus only. 57.03 Error Hp Laserjet P3015 HP COLOR LASER PRINTER 8500, 8550 ERROR 57.3 1. These are small rectangular blocks of plastic which contact the switches in the printer.

If that works go back to the first application and try printing a different file to determine if the problem is file related.

You may need to reseat the memory DIMM's or replace the firmware DIMM or formatter board. You can verify this by substituting a known good DC controller if possible. The information contained on this chip is dependent on the printer model and the supply. Rh7-5295-000cn controller board.HP LASER PRINTER 8100, 8150 ERROR 57.51.

If the board becomes defective, you will receive an error 12. by david belton on Mar 27, 2003 at 5:30am Add comment Please sign in to comment 0 Could also be a hard turning fuser. Reseat DIMM, then Formatter - Replace or flash DIMM then formatter Back back to top How did we do? check over here Results 1 to 3 of 3 Thread: LaserJet 4: 57 Service & 57 Fuser Messages Thread Tools Show Printable Version Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

HP LASER PRINTER 3380, 3390, 33921. If you don't hear the motor immediately and you don't have a paper jam, change the power supply. Verify SIMM's are seated properly, replace any defective 5Si 59.X Main motor malfunciton X=1: Main motor startup failure, X=2: Main motor rotation 59.XY 4200/4300 Series Main motor failure, check wiring harness I am looking in particular for the error code 57 on an HP > laser jet 4. > Thanks, > Robert -- Jeff

Back back to top How did we do? On the 4P/5P printers, the top cover is open or no toner cartridge is installed. Fan operation occurs only during power up or during a print job.2. Reply 0 0 Auddie14 Honor Student Posts: 4 Member Since: ‎11-03-2014 Message 4 of 5 (2,566 Views) Report Inappropriate Content Re: Printer Error code 57.04 Options Mark as New Bookmark Subscribe

The message is on the printer itself. For 57 SERVICE message manual says: Main Motor Functional Checks • Inspect the gear train for debris that would block the free operation of the gears. • Check the gears in On the 4V/4MV check the toner cartridge micro switch on the High Voltage PCB - SW501. Sensor Arm Stuck or Broken - check for free movement of the sensor arm.

© Copyright 2017 batteryuniveristy.com. All rights reserved.