Home > Error Code > Hp Error 13

Hp Error 13

Contents

Misadjusted or bent switchback assembly. With the printer still turned on, disconnect the power cable from the back of the printer. Verify that solenoid SL3 is firmly seated on ECU connector J504. Wrong length paper or incorrect software paper size selected. 7. his comment is here

Replaced the diverter if the paper still doesn't make out of exit.11. The printer would of course, like to print again since it did not complete a "good print sequence"(one without an error).In my previous note I mentioned that I replaced the exit By creating an account, you're agreeing to our Terms of Use and our Privacy Policy Not a member? Toner cartridge gears worn or damaged. 2. https://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/HP-LaserJet-M1212nf-MFP-Scanner-Error-13/td-p/3404477

Hp Printer Error Codes List

Change maintenance kit HP LASER PRINTER 5SI, 8000,8150 1. Re: Printer Laserjet 600 M602 error 13.b9.ff Jam in top cover ereaOptions‎05-14-2014 12:16 PMThe event code: 13.B9.FF indicates that the printer believes there is a jam at the fuser output sensor, Page 221: Component tests These tests activate the selected component. 1.

NOTE: The transfer-roller removal hook is included with a transfer-roller replacement kit. Rotate the media in the input tray by 180° and/or turn it over 13.10 PAPER JAM CHECK DUPLEXER Jam at duplexer 1. Run test with one device taken off one at a time. 14. Hp Printer Error Code List Pdf Bad delivery mechanism or coupler gear to main drive. 13.

Check connector cables on the DC Controller. 5. Hp Laptop Error Codes Paper jam- internally. 4. Use the Tray/Bin manual sensor test to verify that the cassette media switch is correctly functioning. Reply 0 0 Everyone's Tags: FirstContact View All (1) « Message Listing « Previous Topic Next Topic » Related Documents Testing Your HP Fax Machine with the HP Fax Test ServiceHP

Maybe need to exchange scanner part Reply 0 0 kusanjiv Intern Posts: 37 Member Since: ‎03-28-2013 Message 4 of 4 (1,044 Views) Report Inappropriate Content Re: scanner error 13 problem solution Hp Error Code Oxc4eb827f Would it be worth while replacing them? If not, come back and we'll try something else. Worn feed and separation rollers.6.

Hp Laptop Error Codes

On your video I believe it used the phrase "rebuilding the exit assembly". visit It could be a scrap of paper where you can't see it, or the paper sensor might be bad. 1 Datil OP [email protected] Aug 1, 2016 at 10:22 Hp Printer Error Codes List Bad D.C. Hp Computer Error Codes Open the following menus: ● Administration ● Troubleshooting ● Diagnostic Tests 3.

Bad input unite.5. this content Paper jam- check middle front drawer and duplex drawer. 3. It could also be the sensor itself which is on a board with another sensor attached to the PIU unit. check fuser ass'y for paper stopping at the fuser. Hp Inkjet Printer Error Codes

If it is not enabled/started, Make sure to enable/start the service. Open the following menus: • Administration • Troubleshooting • Diagnostic Tests 5. That is the 2 vertical black plastic posts that the flag moves in and out of. weblink Make sure no jam in stapler / stacker.

Page 34: Cassette media size detection and cassette presence detection The media size detection switch (SW102) detects the size of media loaded in the cassette and the presence of the cassette. Hp Printer Error Symbols Recommended action Make sure that the feeder is loaded with the correct paper size and that the sliding paper guides are correctly adjusted. Verify the paper tray is fully closed. 3.

Bad shutter door on toner cartridges.

Use the arrow buttons to select the particular component test that you want to perform, and then press the OK button. Check the input area for obstructions such as media in the path. If the message persists after all media is removed: Check if media is jammed in the prefeed area. Hp Printer Error Code 79 HP LASER PRINTER 5000, 5100, 52001.

It prints, and as the paper exits, it stops, the display says error 13, paper jam. and may not be used without advance written permission of PrinterTechs.com, Inc. Bad fuser ass'y5. check over here Click the “Kudos Thumbs Up" to say “Thanks” for helping!

The only possibilities are that somewhere in the linkage between the fuser and that exit sensor, something is amiss. Verify that SL2 is being energized by removing the cover and observing the solenoid during a feed operation.5. Reseat the fuser. 3. Check paper trays for missed loaded paper. 3.

Unplug all external device and run test with just the printer.7. If the heartbeat LED is off, turn the product power off, make sure that the formatter is fully seated, and then turn the product on. No pick or media jammed in printer.Check the entire paper path of the printer. 2. Wait 10 seconds and reconnect the power cable back to the wall outlet first, then the back of the printer and power it on again.Make sure the printer is connected directly

HP LASER PRINTER 9000, 9040, 9050MFP 1. Defective sensor cable. 2. Viewing the event log from the Service menu 1. Paper stuck in paper path.5.

Defective output rollers. 7. Skin oils on the roller can cause print-quality problems. Gemini02 I work on behalf of HPClick the Thumbs Up below to say “Thanks” for helping! Solution: Check the product for a jam.

Bad middle drawer ass'y. 7. Defective registration guide.

© Copyright 2017 batteryuniveristy.com. All rights reserved.