Hold down CANCEL JOB while turning the printer on. Print a configuration page and check the printer settings to determine which values have changed.2. A poor-quality parallel cable or network cable.3. This error can occur if the driver being used is not IEEE-1284 compliant. http://batteryuniveristy.com/error-code/hp-error-codes.php
HP has already checked for updates and software for your product Option 2: Go directly to the software and driver results How to Matching articles Troubleshooting Matching articles Product Information Matching Turn the power off and wait for 30 seconds then turn the power back on. c. Disconnect the parallel cable or the network cable4. http://support.hp.com/us-en/product/HP-LaserJet-2000-Printer-series/416419/model/412132/troubleshooting
alternates with 59.XY PRINTER ERROR To continue turn off then on Description A temporary printing error occurred. For 68.1 errors: a. Back back to top How did we do? Please enter a Product Number to complete the request.
Also try printing from a different application. Remove all EIO cards and reinstall them to ensure they are seated correctly. 4. Reseat the hard disk.2. Hp Printer Error Code List Pdf Verify that the scanner motor connector is firmly seated in connector J402 on the ECU.
This cleans up the permanent storage by removing old areas that are not being used. Unable to determine warranty status We are unable to determine your warranty status for the product and serial number provided. Back back to top How did we do? If the above action does not solve the issue, reload the tray with the correct paper size.
Any help here would be appreciated too. Hewlett Packard Laptop Error Codes CAUTION: Ensure that all jammed paper is removed before closing the cover or tray. This process can take several minutes depending on the number of warranties being checked. Configure is properly.
Press the Check button one more time to Print Menu Map and then press the Check button. What to do:Check the all toners are installed correctly and that all covers are closed properly. Hp Printer Error Code 49 Perform NVRAM initialization by holding down the ( Reset ) button for more than 20 seconds while power on the printer.2. Hp Laptop Error Codes Defective formatter board.
Loose toner should clear from the printer after a few pages are printed. http://batteryuniveristy.com/error-code/hp-mfp-error-codes.php Turn the MFP off. 7 Remove all DIMMs and flash memory cards, Do not remove the firmware memory card that is in slot 8. Replace formatter board. top 66.12.XX OUTPUT DEVICE FAILURE For help press? Hp Computer Error Codes
CAUTION: To prevent damage to the print cartridge, do not expose it to light for more than a few minutes. If message persists turn printer off then on. 4. A switch on this assembly may not be activated properly. http://batteryuniveristy.com/error-code/hp-lj-error-codes.php Check these items.
top 60.X PRINTER ERROR Description A tray [X] that was opened or filled is trying to lift into position, but there is an obstruction in the tray. Hp Error Code Oxc4eb827f Also, can I get some instructions on putting in the rollers. If the error persists, replace the laser scanner assembly.
Replace the formatter. Press STOP to clear all print jobs from the printer memory. 4. Restart printer. Hp Inkjet Printer Error Codes Turn the printer off and then on.
Was the information on this page helpful? top 13.98.00 OPEN INPUT TRAYS THEN OPEN AND CLOSE TOP COVER Description The rear output bin was opened when the printer was attempting to send a page to the duplexer, a Check the connectors on the DC controller and power supply. http://batteryuniveristy.com/error-code/htc-error-codes.php Be careful not to spill it on yourself or into the printer.) NOTE: NNOTE: If the jammed paper is difficult to remove, try opening the top cover all the way to
alternates with 41.X PRINTER ERROR To continue press (Select) Description A temporary printer error has occurred. To avoid minor burns, wait 30 minutes for the fuser to cool before removing it from the printer. This board takes the input from the two sensors and provides info to the DC controller. Ensure that tray is not over-filled or damaged.
Figure 40: Inserting fuser Install the rear output bin. Check the FFC connection between the formatter and the scanner. 5. Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations Thank you!
Temporary error, Cycle power on and off. 2. alternates with 41.3 LOAD TRAY XX: [Type] [SIZE] For help press ? If after replacing the laser/scanner, the message persists, replace the ECU. Could be a bad cable or loose connection or just a poor quality cable.
If message still there when the network cable is disconnected. Check the FFC connection between the formatter and the scanner. 4. Check that the laser/scanner motor connector is firmly seated in connector J402 on the ECU. 4.